參數資料
型號： EVAL-AD5391EBZ
廠商： Analog Devices Inc
文件頁數： 25/44頁
文件大?。?/td> 0K
描述： BOARD EVALUATION FOR AD5391
產品培訓模塊： DAC Architectures
標準包裝： 1
DAC 的數量： 16
位數： 12
采樣率（每秒）： 167k
數據接口： 串行
設置時間： 6µs
DAC 型： 電壓
工作溫度： -40°C ~ 85°C
已供物品： 板，CD
已用 IC / 零件： AD5391
相關產品： AD5391BSTZ-5-ND - IC DAC 12BIT 16CHAN 3V 52LQFP
AD5391BSTZ-3-ND - IC DAC 12BIT 16CHAN 3V 52LQFP
AD5391BCPZ-5-REEL7-ND - IC DAC 12BIT 16CHAN 5V 64LFCSP
AD5391BCPZ-5-REEL-ND - IC DAC 12BIT 16CHAN 5V 64-LFCSP
AD5391BCPZ-3-ND - IC DAC 12BIT I2C 16CH 3V 64LFCSP
AD5391BCPZ-5-ND - IC DAC 12BIT 16CH 5V 64-LFCSP
Data Sheet
AD5390/AD5391/AD5392
Rev. E | Page 31 of 44
AD539x ON-CHIP SPECIAL FUNCTION REGISTERS
The AD539x family of parts contains a number of special
function registers (SFRs) as shown in Table 22. SFRs are
addressed with REG1 = 0 and REG0 = 0 and are decoded
using Address Bit A3 to Bit A0.
Table 22. SFR Register Functions (REG1 = 0, REG0 = 0)
R/ W
A3
A2
A1
A0
Function
X
0
NOP (no operation)
0
1
Write CLR code
0
1
0
Soft CLR
0
1
0
Soft power-down
0
1
0
1
Soft power-up
0
1
0
Control register write
1
0
Control register read
0
1
0
1
0
Monitor channel
0
1
Soft reset
SFR Commands
NOP (No Operation)
REG1 = REG0 = 0, A3 to A0 = 0000
Performs no operation, but is useful in readback mode to clock
out data on SDO for diagnostic purposes. BUSY outputs a low
during a NOP operation.
Write CLR Code
REG1 = REG0 = 0, A3 to A0 = 0001
DB13 to DB0 = Contain the CLR data
Bringing the CLR line low or exercising the soft clear function
loads the contents of the DAC registers with the data contained
in the user-configurable CLR register and sets VOUT 0 to
VOUT 15, accordingly. This can be very useful not only for
setting up a specific output voltage in a clear condition but for
calibration purposes. For calibration, the user can load full scale
or zero scale to the clear code register and then issue a hardware
or software clear to load this code to all DACs, removing the
need for individual writes to all DACs. Default on power-up
is all zeros.
Soft CLR
REG1 = REG0 = 0, A3 to A0 = 0010
DB13 to DB0 = Don’t Care
Executing this instruction performs the CLR, which is
functionally the same as that provided by the external CLR pin.
The DAC outputs are loaded with the data in the CLR code
register. The time taken to execute fully the SOFT CLR is
20 s on the AD5390/AD5391 and 15 s on the AD5392. It
is indicated by the BUSY low time.
Soft Power-Down
REG1 = REG0 = 0, A3 to A0 = 1000
DB13 to DB0 = Don’t Care
Executing this instruction performs a global power-down,
which puts all channels into a low power mode, reducing analog
current to 1 A maximum and digital power consumption to
20 A maximum. In power-down mode, the output amplifier
can be configured as a high impedance output or can provide a
100 k load to ground. The contents of all internal registers are
retained in power-down mode.
Soft Power-Up
REG1 = REG0 = 0, A3 to A0 =1001
DB13 to DB0 = Don’t Care
This instruction is used to power up the output amplifiers and
the internal references. The time to exit power-down mode is
8 s. The hardware power-down and software functions are
internally combined in a digital OR function.
Soft Reset
REG1 = REG0 = 0, A5 to A0 = 001111
DB13 to DB0 = Don’t Care
This instruction is used to implement a software reset. All
internal registers are reset to their default values, which
correspond to m at full scale and c at zero scale. The contents
of the DAC registers are cleared, setting all analog outputs to
0 V. The soft reset activation time is 135 s maximum.
Monitor Channel
REG1 = REG0 = 0, A3 to A0 = 01010
DB13 to DB8 = Contain data to address the channel to be
monitored
A monitor function is provided on all devices. This feature,
consisting of a multiplexer addressed via the interface, allows
any channel output to be routed to the MON_OUT pin for
monitoring using an external ADC. In addition to monitoring
all output channels, two external inputs are also provided,
allowing the user to monitor signals external to the AD539x.
The channel monitor function must be enabled in the control
register before any channels are routed to the MON_OUT pin.
On the AD5390 and AD5392 14-bit parts, DB13 to DB8 contain
the channel address for the monitored channel. On the AD5391
12-bit part, DB11 to DB6 contain the channel address for the
channel to be monitored. Selecting Address 63 three-states the
MON_OUT pin.
The channel monitor decoding for the AD5390/AD5392 is
shown in Table 23 and the monitor decoding for the AD5391 is
shown in Table 24.
相關PDF資料
PDF描述
EMA10DTBH CONN EDGECARD 20POS R/A .125 SLD
EVAL-AD5372EBZ BOARD EVAL FOR AD5372
EVAL-AD5361EBZ BOARD EVAL FOR AD5361
V300C2E50BF3 CONVERTER MOD DC/DC 2V 50W
0210490910 CABLE JUMPER 1.25MM .178M 21POS
相關代理商/技術參數
參數描述
EVAL-AD5392EB 制造商:Analog Devices 功能描述:EVAL BD FOR 8-/16CH, 3V/5 V, SERL INPUT, SGL-SUPPLY,12-/14BI - Bulk
EVAL-AD5392EBZ 功能描述:BOARD EVAL FOR AD5392 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581
EVAL-AD5398AEBZ 制造商:AD 制造商全稱:Analog Devices 功能描述:120 mA, Current Sinking, 10-Bit, I2C DAC
EVAL-AD5398EB 制造商:Analog Devices 功能描述:EVALUATION BOARD I.C. - Bulk 制造商:Rochester Electronics LLC 功能描述:
EVAL-AD5398EBZ 制造商:Analog Devices 功能描述:EVALUATION BOARD I.C. - Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*