- 您現在的位置：買賣IC網 > PDF目錄299034 > EQD020A0F641Z (LINEAGE POWER LLC) 1-OUTPUT 66 W DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | EQD020A0F641Z |
| 廠商： | LINEAGE POWER LLC |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT 66 W DC-DC REG PWR SUPPLY MODULE |
| 封裝： | ROHS COMPLIANT, EIGHTH BRICK-9 |
| 文件頁數： | 15/15頁 |
| 文件大?。?/td> | 272K |
| 代理商： | EQD020A0F641Z |
Data Sheet
November 9, 2006
EQD020 Series Single Output: Eighth Brick Power Modules:
19-60Vdc Input; 3.3Vdc Output; 66W
Tyco Electronics Power Systems
9
Feature Descriptions
Remote On/Off
The EQD020 series power modules have primary
referenced remote On/Off. The remote on/off is open
collector compatible with the signal common
referenced to the negative input. The standard
remote on/off negative logic is such that a unit
operates (ON) when the remote on/off signal is low or
short circuit to minus VIN. A module will be OFF when
the remote on/off pin is open circuit or when the
remote on/off signal is high. Observe the maximum
external ON/OFF voltage, specified in the Feature
Specifications table, when connecting an external
source to the ON/OFF pin. The optional positive logic
remote on/off is such that a unit operates (ON) when
the remote on/off signal is high or open-circuit. A unit
will be OFF when the remote on/off signal is low or
short-circuited to minus VIN.
ON/OFF
VIN(+)
VIN(-)
Ion/off
Von/off
VO
COM
Figure 19. Circuit configuration for using Remote
On/Off Implementation.
Overcurrent Protection
To provide protection in a fault (output overload)
condition, the unit is equipped with internal
current-limiting circuitry and can endure current
limiting continuously. At the point of current-limit
inception, the unit enters a hiccup mode. If the unit is
not configured with auto–restart, then it will latch off
following the over current condition. The module can
be restarted by cycling the dc input power for at least
one second or by toggling the remote on/off signal for
at least one second. If the unit is configured with the
auto-restart option (4), it will remain in the hiccup
mode as long as the overcurrent condition exists; it
operates normally, once the output current is brought
back into its specified range.
Input Under Voltage Lockout
At input voltages below the input under voltage
lockout limit, the module operation is disabled. The
module will begin to operate at an input voltage above
the under voltage lockout turn-on threshold.
Over Temperature Protection
These modules feature an overtemperature protection
circuit to safeguard against thermal damage. The
circuit shuts down and latches off the module when
the maximum device reference temperature is
exceeded. The module can be restarted by cycling
the dc input power for at least one second or by
toggling the remote on/off signal for at least one
second. If the auto-restart option (4) is ordered, the
module will automatically restart upon cool-down to a
safe temperature.
Output Over Voltage Protection
The output over voltage protection scheme of the
modules has an independent over voltage loop to
prevent single point of failure. This protection feature
latches in the event of over voltage across the output.
Cycling the on/off pin or input voltage resets the
latching protection feature. If the auto-restart option
(4) is ordered, the module will automatically restart
upon an internally programmed time elapsing.
Remote sense
The EQD020 series power modules have a Remote
Sense feature to minimize the effects of distribution
losses by regulating the voltage at the Remote Sense
pin (See Figure 20). The voltage between the Sense
pin and Vo pin must not exceed 0.33V.
The amount of power delivered by the module is
defined as the output voltage multiplied by the output
current (Vo x Io). When using Remote Sense, the
output voltage of the module can increase, which, if
the same output is maintained, increases the power
output from the module. Make sure that the maximum
output power of the module remains at or below the
maximum rated power. When the Remote Sense
feature is not being used, connect the Remote Sense
pins to the output pins of the module.
VO(+)
SENSE(+)
SENSE(–)
VO(–)
VI(+)
VI(-)
IO
LOAD
CONTACT AND
DISTRIBUTIONLOSSES
SUPPLY
II
CONTACT
RESISTANCE
Figure 20. Effective Circuit Configuration for
remote sense operation.
相關PDF資料 |
PDF描述 |
|---|---|
| EQW006A0B1-S | 1-OUTPUT 72 W DC-DC REG PWR SUPPLY MODULE |
| EQW025A0Y61Z | 1-OUTPUT 45 W DC-DC REG PWR SUPPLY MODULE |
| EQW025A0Y1Z | 1-OUTPUT 45 W DC-DC REG PWR SUPPLY MODULE |
| EQW012A0A1 | 1-OUTPUT 60 W DC-DC REG PWR SUPPLY MODULE |
| EQXP-HC535R-FREQ1 | CRYSTAL OSCILLATOR, CLOCK, 0.75 MHz - 125 MHz, HCMOS OUTPUT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EQD020A0FZ | 制造商:LINEAGEPOWER 制造商全稱:LINEAGEPOWER 功能描述:Eighth Brick Through-Hole Power Modules |
| EQD075A1 | 功能描述:DC/DC轉換器 5V/3.3V 15A/20A 75W RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| EQD075A1-HZ | 功能描述:DC/DC轉換器 75W 18-60V 5/3.3V 15/20A TH RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| EQD075A4 | 制造商:LINEAGEPOWER 制造商全稱:LINEAGEPOWER 功能描述:18-60Vdc Input; 3.3 to 5.0Vdc Output; 75W |
| EQD075A41 | 功能描述:DC/DC轉換器 TH 75W 15/20A IN 18-60V OUT 5/3.3V RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
發布緊急采購，3分鐘左右您將得到回復。