參數資料
型號: EPF10K30AQI208-3N
廠商: Altera
文件頁數: 62/128頁
文件大?。?/td> 0K
描述: IC FLEX 10KA FPGA 30K 208-PQFP
產品培訓模塊: Three Reasons to Use FPGA's in Industrial Designs
標準包裝: 24
系列: FLEX-10K®
LAB/CLB數: 216
邏輯元件/單元數: 1728
RAM 位總計: 12288
輸入/輸出數: 147
門數: 69000
電源電壓: 3 V ~ 3.6 V
安裝類型: 表面貼裝
工作溫度: -40°C ~ 100°C
封裝/外殼: 208-BFQFP
供應商設備封裝: 208-PQFP(28x28)
Altera Corporation
39
FLEX 10K Embedded Programmable Logic Device Family Data Sheet
Slew-Rate Control
The output buffer in each IOE has an adjustable output slew rate that can
be configured for low-noise or high-speed performance. A slower slew
rate reduces system noise and adds a maximum delay of approximately
2.9 ns. The fast slew rate should be used for speed-critical outputs in
systems that are adequately protected against noise. Designers can specify
the slew rate on a pin-by-pin basis during design entry or assign a default
slew rate to all pins on a device-wide basis. The slow slew rate setting
affects only the falling edge of the output.
Open-Drain Output Option
FLEX 10K devices provide an optional open-drain (electrically equivalent
to an open-collector) output for each I/O pin. This open-drain output
enables the device to provide system-level control signals (e.g., interrupt
and write enable signals) that can be asserted by any of several devices. It
can also provide an additional wired-OR plane. Additionally, the Altera
software can convert tri-state buffers with grounded data inputs to open-
drain pins automatically.
Open-drain output pins on FLEX 10K devices (with a pull-up resistor to
the 5.0-V supply) can drive 5.0-V CMOS input pins that require a VIH of
3.5 V. When the open-drain pin is active, it will drive low. When the pin is
inactive, the trace will be pulled up to 5.0 V by the resistor. The open-drain
pin will only drive low or tri-state; it will never drive high. The rise time
is dependent on the value of the pull-up resistor and load impedance. The
IOL current specification should be considered when selecting a pull-up
resistor.
Output pins on 5.0-V FLEX 10K devices with VCCIO = 3.3 V or 5.0 V (with
a pull-up resistor to the 5.0-V supply) can also drive 5.0-V CMOS input
pins. In this case, the pull-up transistor will turn off when the pin voltage
exceeds 3.3 V. Therefore, the pin does not have to be open-drain.
MultiVolt I/O Interface
The FLEX 10K device architecture supports the MultiVolt I/O interface
feature, which allows FLEX 10K devices to interface with systems of
differing supply voltages. These devices have one set of VCC pins for
internal operation and input buffers (VCCINT) and another set for I/O
output drivers (VCCIO).
相關PDF資料
PDF描述
HSC43DRAH CONN EDGECARD 86POS R/A .100 SLD
552079-1 CONN COVER STR RLF 14POS 180DEG
ABM43DSAS CONN EDGECARD 86POS R/A .156 SLD
EPF10K30AQI208-3 IC FLEX 10KA FPGA 30K 208-PQFP
EP20K100EBC356-3 IC APEX 20KE FPGA 100K 356-BGA
相關代理商/技術參數
參數描述
EPF10K30AQI240-3 功能描述:FPGA - 現場可編程門陣列 FPGA - Flex 10K 216 LABs 189 IOs RoHS:否 制造商:Altera Corporation 系列:Cyclone V E 柵極數量: 邏輯塊數量:943 內嵌式塊RAM - EBR:1956 kbit 輸入/輸出端數量:128 最大工作頻率:800 MHz 工作電源電壓:1.1 V 最大工作溫度:+ 70 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-256
EPF10K30AQI240-3N 功能描述:FPGA - 現場可編程門陣列 FPGA - Flex 10K 216 LABs 189 IOs RoHS:否 制造商:Altera Corporation 系列:Cyclone V E 柵極數量: 邏輯塊數量:943 內嵌式塊RAM - EBR:1956 kbit 輸入/輸出端數量:128 最大工作頻率:800 MHz 工作電源電壓:1.1 V 最大工作溫度:+ 70 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-256
EPF10K30ATC144-1 功能描述:FPGA - 現場可編程門陣列 FPGA - Flex 10K 216 LABs 102 IOs RoHS:否 制造商:Altera Corporation 系列:Cyclone V E 柵極數量: 邏輯塊數量:943 內嵌式塊RAM - EBR:1956 kbit 輸入/輸出端數量:128 最大工作頻率:800 MHz 工作電源電壓:1.1 V 最大工作溫度:+ 70 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-256
EPF10K30ATC144-1N 功能描述:FPGA - 現場可編程門陣列 FPGA - Flex 10K 216 LABs 102 IOs RoHS:否 制造商:Altera Corporation 系列:Cyclone V E 柵極數量: 邏輯塊數量:943 內嵌式塊RAM - EBR:1956 kbit 輸入/輸出端數量:128 最大工作頻率:800 MHz 工作電源電壓:1.1 V 最大工作溫度:+ 70 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-256
EPF10K30ATC1442 制造商:ALTERA 功能描述:*