參數資料
型號： EPC1064
廠商： Altera Corporation
英文描述： Configuration Devices for ACEX, APEX, FLEX & Mercury Devices
中文描述： 配置器件ACEX，頂點，柔性
文件頁數： 7/28頁
文件大小： 380K
代理商： EPC1064
Altera Corporation
7
Configuration Devices for ACEX, APEX, FLEX & Mercury Devices Data Sheet
Device
Configuration
The control signals for configuration devices
—
nCS
,
OE
, and
DCLK
—
interface directly with ACEX, APEX, FLEX, and Mercury device control
signals. All ACEX, APEX, FLEX, and Mercury devices can be configured
by a configuration device without requiring an external intelligent
controller.
The configuration device
’
s
OE
and
nCS
pins control the tri-state buffer on
the
DATA
output pin, and enable the address counter (and the oscillator in
EPC2, EPC1, and EPC1441 devices). When
OE
is driven low, the
configuration device resets the address counter and tri-states its
DATA
pin.
The
nCS
pin controls the output of the configuration device. If
nCS
is held
high after the
OE
reset pulse, the counter is disabled and the
DATA
output
pin is tri-stated. When
nCS
is driven low, the counter and
DATA
output pin
are enabled. When
OE
is driven low again, the address counter is reset and
the
DATA
output pin is tri-stated, regardless of the state of
nCS
.
1
The EPC2, EPC1, and EPC1441 devices determine the operation
mode and whether the ACEX 1K, APEX 20K, FLEX 10K,
FLEX 8000, FLEX 6000, or Mercury protocols should be used
when
OE
is driven high.
When the configuration device has driven out all of its data and has
driven
nCASC
low, the device tri-states the
DATA
pin to avoid contention
with other configuration devices.
The EPC2 device allows the user to initiate configuration of the ACEX,
APEX, FLEX, or Mercury device via an additional pin,
nINIT_CONF
, that
can be tied to the
nCONFIG
pin of the ACEX, APEX, FLEX, or Mercury
device(s) to be configured. A JTAG instruction causes the EPC2 device to
drive
nINIT_CONF
low, which in turn pulls
nCONFIG
low. The EPC2
device then drives
nINIT_CONF
high to start configuration. When the
JTAG state machine exits this state,
nINIT_CONF
releases
nCONFIG
and
configuration is initiated.
1
An EPC2 device can be programmed with a POF generated for
an EPC1 or EPC1441 device, however, an EPC2 device cannot
configure FLEX 6000 or FLEX 8000 devices. An EPC1 device can
be programmed using a POF
generated for an EPC1441 device.
相關PDF資料
PDF描述
EPC1064V Configuration Devices for ACEX, APEX, FLEX & Mercury Devices
EPC1213 Configuration Devices for ACEX, APEX, FLEX & Mercury Devices
EPC1441 Configuration Devices for ACEX, APEX, FLEX & Mercury Devices
EPC4xxx 2. Enhanced Configuration Devices (EPC4, EPC8 & EPC16) Data Sheet
EPC16QC100 2. Enhanced Configuration Devices (EPC4, EPC8 & EPC16) Data Sheet
相關代理商/技術參數
參數描述
EPC1064LC20 功能描述:FPGA-配置存儲器 IC - Ser. Config Mem Flash 64Kb 6 MHz RoHS:否 制造商:Altera Corporation 存儲類型:Flash 存儲容量:1.6 Mbit 工作頻率:10 MHz 電源電壓-最大:5.25 V 電源電壓-最小:3 V 電源電流:50 uA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-20
EPC1064LC-20 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Configuration EPROM
EPC1064LI20 功能描述:IC CONFIG DEVICE 65KBIT 20-PLCC RoHS:否 類別:集成電路 (IC) >> 存儲器 - 用于 FPGA 的配置 Proms 系列:EPC 產品變化通告:Product Discontinuation 28/Jul/2010 標準包裝:98 系列:- 可編程類型:OTP 存儲容量:300kb 電源電壓:3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-TSOP 包裝:管件
EPC1064LI-20 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Configuration EPROM
EPC1064PA1 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*