- 您現在的位置：買賣IC網 > PDF目錄362702 > EN29LV400AT-70TIP (Electronic Theatre Controls, Inc.) Replaced by PTH04070W : PDF資料下載
參數資料
| 型號： | EN29LV400AT-70TIP |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Replaced by PTH04070W : |
| 中文描述： | 4兆位（為512k × 8位/ 256 × 16位）閃存引導扇區閃存，CMOS 3.0伏，只 |
| 文件頁數： | 8/41頁 |
| 文件大?。?/td> | 771K |
| 代理商： | EN29LV400AT-70TIP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁
USER MODE DEFINITIONS
Word / Byte Configuration
The signal set on the BYTE# Pin controls whether the device data I/O pins DQ15-DQ0 operate in
the byte or word configuration. When the Byte# Pin is set at logic ‘1’, then the device is in word
configuration, DQ15-DQ0 are active and are controlled by CE# and OE#.
On the other hand, if the Byte# Pin is set at logic ‘0’, then the device is in byte configuration, and
only data I/O pins DQ0-DQ7 are active and controlled by CE# and OE#. The data I/O pins DQ8-
DQ14 are tri-stated, and the DQ15 pin is used as an input for the LSB (A-1) address function.
Standby Mode
The EN29LV400A has a CMOS-compatible standby mode, which reduces the
current to
<
1μA
(typical). It is placed in CMOS-compatible standby when the CE# pin is at V
CC
±
0.5. RESET# and
BYTE# pin must also be at CMOS input levels. The device also has a TTL-compatible standby mode,
which reduces the maximum V
CC
current to < 1mA. It is placed in TTL-compatible standby when the
CE# pin is at V
IH
. When in standby modes, the outputs are in a high-impedance state independent
of the OE# input.
Read Mode
The device is automatically set to reading array data after device power-up. No commands are
required to retrieve data. The device is also ready to read array data after completing an Embedded
Program or Embedded Erase algorithm.
After the device accepts an Erase Suspend command, the device enters the Erase Suspend mode.
The system can read array data using the standard read timings, except that if it reads at an address
within erase-suspended sectors, the device outputs status data. After completing a programming
operation in the Erase Suspend mode, the system may once again read array data with the same
exception. See “Erase Suspend/Erase Resume Commands” for more additional information.
The system must issue the reset command to re-enable the device for reading array data if DQ5
goes high, or while in the autoselect mode. See the “Reset Command” additional details.
Output Disable Mode
When the OE# pin is at a logic high level (VIH), the output from the EN29LV400A is disabled. The
output pins are placed in a high impedance state.
Auto Select Identification Mode
The autoselect mode provides manufacturer and device identification, and sector protection
verification, through identifier codes output on DQ15–DQ0. This mode is primarily intended for
programming equipment to automatically match a device to be programmed with its corresponding
programming algorithm. However, the autoselect codes can also be accessed in-system through the
command register.
When using programming equipment, the autoselect mode requires V
ID
(10.5V to 11.5 V) on
address pin A9. Address pins A8, A6, A1, and A0 must be as shown in Autoselect Codes table. In
addition, when verifying sector protection, the sector address must appear on the appropriate
highest order address bits. Refer to the corresponding Sector Address Tables. The Command
Definitions table shows the remaining address bits that are don’t-care. When all necessary bits have
been set as required, the programming equipment may then read the corresponding identifier code
on DQ15–DQ0.
This Data Sheet may be revised by subsequent versions 2005 Eon Silicon Solution, Inc., www.essi.com.tw
or modifications due to changes in technical specifications.
Rev. A, Issue Date: 2005/01/07
EN29LV400A
相關PDF資料 |
PDF描述 |
|---|---|
| EN29LV400AT-90BC | Replaced by PTH04070W : |
| EN29LV400AT-90BCP | Replaced by PTH04070W : |
| EN29LV400AT-90BI | Replaced by PTH04070W : |
| EN29LV400AT-90BIP | Replaced by PTH04070W : |
| EN29LV400AT-90TC | Replaced by PTH04070W : |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EN29LV800AB-70TC | 制造商:Eon Silicon Solution Inc 功能描述: |
| EN29LV800BB-70TCP | 制造商:EON SILICON SOLUTION INC 功能描述:EN29LV800B Series, 8 Mbit 70 NS 48 TSOP 3 V Bottom Boot Sector NOR Flash |
| EN29LV800CT-70TIP | 制造商:EON SILICON SOLUTION INC 功能描述:8mb TSOP 70ns nor flash |
| EN29SL400B-90BIP | 制造商:EON SILICON SOLUTION INC 功能描述:EN29SL400 Series, 4 Mbit 90 NS 48 FBGA 1.8 V Bottom Boot Sector NOR Flash |
| EN2-B1H1 | 制造商:NEC 制造商全稱:NEC 功能描述:AUTOMOTIVE RELAYS (Twin, Single) Relays |
發布緊急采購，3分鐘左右您將得到回復。