- 您現在的位置：買賣IC網 > PDF目錄364740 > EN25F80-75VCP (Eon Silicon Solution Inc.) 4 Mbit Uniform Sector, Serial Flash Memory PDF資料下載
參數資料
| 型號： | EN25F80-75VCP |
| 廠商： | Eon Silicon Solution Inc. |
| 元件分類： | FLASH |
| 英文描述： | 4 Mbit Uniform Sector, Serial Flash Memory |
| 中文描述： | 4兆位統一部門，串行閃存 |
| 文件頁數： | 10/33頁 |
| 文件大?。?/td> | 469K |
| 代理商： | EN25F80-75VCP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
This Data Sheet may be revised by subsequent versions 2004 Eon Silicon Solution, Inc., www.essi.com.tw
or modifications due to changes in technical specifications.
Rev. D, Issue Date: 2007/05/16
EN25F80
Manufacturer/
Device ID
Read Identification
Enter OTP mode
Notes:
1. Data bytes are shifted with Most Significant Bit first. Byte fields with data in parenthesis “( )” indicate data being read from
the device on the DO pin.
2. The Status Register contents will repeat continuously until CS# terminate the instruction.
3. All sectors may use any address within the sector.
4. The Device ID will repeat continuously until CS# terminate the instruction.
5. The Manufacturer ID and Device ID bytes will repeat continuously until CS# terminate the instruction.
00h on Byte 4 starts with MID and alternate with DID, 01h on Byte 4 starts with DID and alternate with MID.
Table 5. Manufacturer and Device Identification
90h
dummy
dummy
00h(5)
(M7-M0)
(ID7-ID0)
9Fh
3Ah
(M7-M0)
(ID15-ID8)
(ID7-ID0)
OP Code
(M7-M0)
(ID15-ID0)
(ID7-ID0)
ABh
13h
90h
1Ch
13h
9Fh
1Ch
3114h
Write Enable (WREN) (06h)
The Write Enable (WREN) instruction (Figure 5)
Latch (WEL) bit must be set prior to every Page Program (PP), Sector Erase (SE), Block Erase (BE), Chip
Erase (CE) and Write Status Register (WRSR) instruction.
The Write Enable (WREN) instruction is entered by driving Chip Select (CS#) Low, sending the instruction
code, and then driving Chip Select (CS#) High.
sets the Write Enable Latch (WEL) bit. The Write Enable
Write Disable (WRDI) (04h)
The Write Disable instruction (Figure 6) resets the Write Enable Latch (WEL) bit in the Status Register to
a 0 or exit from OTP mode to normal mode. The Write Disable instruction is entered by driving Chip
Select (CS#) low, shifting the instruction code “04h” into the DI pin and then driving Chip Select (CS#)
high. Note that the WEL bit is automatically reset after Power-up and upon completion of the Write Status
Register, Page Program, Sector Erase, Block Erase (BE) and Chip Erase instructions.
相關PDF資料 |
PDF描述 |
|---|---|
| EN25F80-75VI | 4 Mbit Uniform Sector, Serial Flash Memory |
| EN25F80-75VIP | 4 Mbit Uniform Sector, Serial Flash Memory |
| EN25P05 | 4 Mbit Uniform Sector, Serial Flash Memory |
| EN25P05-100GC | 4 Mbit Uniform Sector, Serial Flash Memory |
| EN25P05-100GCP | 4 Mbit Uniform Sector, Serial Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EN25F80-75VI | 制造商:EON 制造商全稱:Eon Silicon Solution Inc. 功能描述:8 Mbit Serial Flash Memory with 4Kbytes Uniform Sector |
| EN25F80-75VIP | 制造商:EON 制造商全稱:Eon Silicon Solution Inc. 功能描述:8 Mbit Serial Flash Memory with 4Kbytes Uniform Sector |
| EN25LF05 | 制造商:EON 制造商全稱:Eon Silicon Solution Inc. 功能描述:512 Kbit Serial Flash Memory with 4Kbytes Uniform Sector |
| EN25LF05-75GI | 制造商:EON 制造商全稱:Eon Silicon Solution Inc. 功能描述:512 Kbit Serial Flash Memory with 4Kbytes Uniform Sector |
| EN25LF05-75GIP | 制造商:EON 制造商全稱:Eon Silicon Solution Inc. 功能描述:512 Kbit Serial Flash Memory with 4Kbytes Uniform Sector |
發布緊急采購，3分鐘左右您將得到回復。