參數資料
型號: EMC2103-1-KP-TR
廠商: STANDARD MICROSYSTEMS CORP
元件分類: 模擬信號調理
中文描述: SPECIALTY ANALOG CIRCUIT, QCC12
封裝: 4 X 4 MM, ROHS COMPLIANT, QFN-12
文件頁數: 48/89頁
文件大小: 1243K
代理商: EMC2103-1-KP-TR
RPM-Based Fan Controller with HW Thermal Shutdown
Datasheet
Revision 0.90 (08-19-08)
52
SMSC EMC2103
DATASHEET
6.11
Configuration 2 Register
The Configuration 2 Register controls conversion rate of the temperature monitoring as well as the
fault queue.
Bit 6 - DIS_DYN - Disables the Dynamic Averaging Feature.
‘0’ (default) - The Dynamic Averaging function is enabled. The conversion time for all temperature
channels is scaled based on the chosen conversion rate to maximize accuracy and immunity to
random temperature measurement variation.
‘1’ - The Dynamic Averaging function is disabled. The conversion time for all temperature channels
is fixed regardless of the chosen conversion rate.
Bit 5 - DIS_TO - Disables the SMBus time out function.
‘0’ (default) - The SMBus time out function is enabled.
‘1’ - The SMBus time out function is disabled allowing the device to be fully I2C compliant.
Bit 4 - DIS_AVG - Disables digital averaging of the External Diode channels.
‘0’ (default) - The External Diode channels have digital averaging enabled. The temperature data
is the average of the previous four measurements.
‘1’ - The External Diode channels have digital averaging disabled. The temperature data is the last
measured data.
Bits 3-2 - QUEUE[1:0] - Determines the number of consecutive out of limit conditions that are
necessary to trigger an interrupt. Each measurement channel has a separate fault queue associated
with the high limit, low limit, and diode fault condition.
APPLICATION NOTE: If the fault queue for any channel is currently active (i.e. an out of limit condition has been
detected and caused the fault queue to increment) then changing the settings will not take
effect until the fault queue is zeroed. This occurs by the ALERT pin asserting or the out of
limit condition being removed.
Bit 1 - 0 - CONV[1:0] - determines the conversion rate of the temperature monitoring. This conversion
rate does not affect the fan driver. The supply current from VDD_3V is nominally dependent upon the
conversion rate and the average current will increase as the conversion rate increases.
Table 6.16 Configuration 2 Register
ADDR
R/W
REGISTER
B7
B6
B5
B4
B3
B2
B1
B0
DEFAULT
21h
R/W
Config 2
-
DIS_D
YN
DIS_
TO
DIS_
AVG
QUEUE[1:0]
CONV[1:0]
0Eh
Table 6.17 Fault Queue
QUEUE[1:0]
NUMBER OF CONSECUTIVE OUT OF LIMIT CONDITIONS
10
0
1 (disabled)
01
2
10
3
1
4 (default)
相關PDF資料
PDF描述
EMC2103-2-AP-TR
EMCL12C2J-35.000MTR CRYSTAL OSCILLATOR, CLOCK, 35 MHz, LVPECL OUTPUT
EMCL12C2J-40.000M CRYSTAL OSCILLATOR, CLOCK, 40 MHz, LVPECL OUTPUT
EMCL12D2H-30.000MTR CRYSTAL OSCILLATOR, CLOCK, 30 MHz, LVPECL OUTPUT
EMCL12D2H-40.000MTR CRYSTAL OSCILLATOR, CLOCK, 40 MHz, LVPECL OUTPUT
相關代理商/技術參數
參數描述
EMC2103-2 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Analog and Interface Product Selector Guide
EMC2103-2-AP 制造商:SMSC 制造商全稱:SMSC 功能描述:RPM-Based Fan Controller with HW Thermal Shutdown
EMC2103-2-AP-TR 功能描述:板上安裝溫度傳感器 Closed Loop RPM RPM Fan Ctrl 3Remote RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
EMC2103-3-KP 制造商:SMSC 制造商全稱:SMSC 功能描述:RPM-Based Fan Controller with HW Thermal Shutdown
EMC2103-4 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Analog and Interface Product Selector Guide