參數資料
型號： EM785830AAP
廠商： ELAN Microelctronics Corp .
英文描述： 8-BIT MICRO-CONTROLLER
中文描述： 8位微控制器
文件頁數： 30/43頁
文件大?。?/td> 396K
代理商： EM785830AAP
EM785830AA
8-bit Micro-controller
__________________________________________________________________________________________________________________________________________________________________
* This specification is subject to be changed without notice.
12/1/2004 V1.6
VII.5 RESET
The RESET can be caused by
(1) Power on reset
(2) WDT timeout. (if enabled and in GREEN or NORMAL mode)
(3) /RESET pin pull low
Once the RESET occurs, the following functions are performed.
The oscillator is running, or will be started.
The Program Counter (R2) is set to all "0".
When power on, the upper 3 bits of R3 and the upper 2 bits of R4 are cleared.
The Watchdog timer and prescaler counter are cleared.
The Watchdog timer is disabled.
The CONT register is set to all "1"
The other register (bit 7 ~ bit 0) default values are as follows.
Operation registers :
Address
R register
PAGE0
PAGE1
0x4
00xxxxxx
0x5
xxxx0000
xxxx0000
0x6
xxxxxxxx
xxxxxxxx
0x7
xxxxxxxx
xxxx0000
0x8
xxxxxxxx
00000000
0x9
xxxxxxxx
xxxxxxxx
0xA
00011xx0
11111111
0xB
xxxxxxxx
xxxxxxxx
0xC
xxxxxxxx
00000000
0xD
xxxxx000
00000000
0xE
00000000
0xF
00000000
VII.6 Wake-up
The controller provided sleep mode for power saving :
SLEEP mode, RA(7) = 0 + "SLEP" instruction
The controller will turn off all the CPU and crystal. Other circuit with power control like key tone control or
PLL control (which has enable register), user has to turn it off by software.
Wake-up from SLEEP mode
(1) WDT time out
(2) External interrupt
(3) /RESET pull low
All these cases will reset controller , and run the program at address zero. The status just like the power on reset.
VII.7 Interrupt
RF is the interrupt status register which records the interrupt request in flag bit. IOCF is the interrupt mask
register. Global interrupt is enabled by ENI instruction and is disabled by DISI instruction. When one of the
interrupts (when enabled) generated, will cause the next instruction to be fetched from address 008H. Once in the
interrupt service routine, the source of the interrupt can be determined by polling the flag bits in the RF register.
The interrupt flag bit must be cleared in software before leaving the interrupt service routine and enabling
interrupts to avoid recursive interrupts.
R register
R register
PAGE2
00000000
xxxxxxxx
0x000000
xxxxxxxx
xxxxxxxx
xxxxxxxx
xxxxxxxx
R register
PAGE3
00000000
00000000
xxxxxx00
00000000
00000000
xxxxxx00
00000000
IOC register
PAGE0
111x0000
11111111
11111111
11111111
11111111
xxxxxxxx
11111111
11111111
xxxxxxxx
0000xxxx
00000000
IOC register
PAGE1
00000000
00000000
00000000
00000000
x0xx0xx
000000x0
00000000
00000000
xxxxxxxx
相關PDF資料
PDF描述
EM785830AD 8-BIT MICRO-CONTROLLER
EM785830ADQ 8-BIT MICRO-CONTROLLER
EM78P5830AA 8-BIT MICRO-CONTROLLER
EM78P5830AAM 8-BIT MICRO-CONTROLLER
EM78P5830AAP 8-BIT MICRO-CONTROLLER
相關代理商/技術參數
參數描述
EM785830AD 制造商:EMC 制造商全稱:ELAN Microelectronics Corp 功能描述:8-BIT MICRO-CONTROLLER
EM785830ADQ 制造商:EMC 制造商全稱:ELAN Microelectronics Corp 功能描述:8-BIT MICRO-CONTROLLER
EM785840 制造商:EMC 制造商全稱:ELAN Microelectronics Corp 功能描述:8-BIT MICRO-CONTROLLER
EM785840M 制造商:EMC 制造商全稱:ELAN Microelectronics Corp 功能描述:8-BIT MICRO-CONTROLLER
EM785840P 制造商:EMC 制造商全稱:ELAN Microelectronics Corp 功能描述:8-BIT MICRO-CONTROLLER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*