- 您現在的位置：買賣IC網 > PDF目錄362657 > ELANSC400-66AC (ADVANCED MICRO DEVICES INC) Single-Chip, Low-Power, PC/AT-Compatible Microcontrollers PDF資料下載
參數資料
| 型號： | ELANSC400-66AC |
| 廠商： | ADVANCED MICRO DEVICES INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | Single-Chip, Low-Power, PC/AT-Compatible Microcontrollers |
| 中文描述： | 32-BIT, FLASH, 66 MHz, MICROCONTROLLER, PBGA292 |
| 封裝： | PLASTIC, BGA-292 |
| 文件頁數： | 74/132頁 |
| 文件大?。?/td> | 2400K |
| 代理商： | ELANSC400-66AC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁當前第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁
74
élanSC400 and élanSC410 Microcontrollers Data Sheet
Using the Configuration Pins to Select
Pin Functions
The configuration pins are used only for those func-
tions that must be selected at reset, prior to firmware
execution. All other I/O functions are selected using
configuration registers.
Table 21 provides an overview of the configuration pin
functions. All of the CFG pins have weak internal pull-
down resistors that select the default function. External
pullup resistors are required to select an alternative
function.
Notes:
1. CFG3 is defined as the enable/disable for the DBUFOE,
DBUFRDL, and DBUFRDH signals. They can be enabled
independently of whether a x32 D bus is selected via the
firmware to support the VL local bus or x32 DRAM interface.
2. The x32 ROM option must be selected for ROMCS0 for
the R32BFOE signal to be enabled. The selection of the
DBUFOE, DBUFRDL, and DBUFRDH signals are still
dependent only on the CFG3 signal.
CFG0 and CFG1 Pins
These pins (shown in Table 22) configure the data bus
width (x8, x16, or x32) of the ROM interface that is se-
lected by the ROMCS0 pin. If a x32 ROM is selected,
these pins also enable the ROM x32 Data Bus Buffer
Output Enable signal (R32BFOE). If a 32-bit data bus
width is selected for the ROM interface, the R32BFOE
signal will be asserted for all ROMCSx accesses to
32-bit ROM. Exercise caution because the data bus
width for the ROMCS0 interface can also be changed
through programming. This feature was implemented
mainly for testing.
.
CFG2 Pin—élanSC400 Microcontroller Only
This configuration pin (see Table 23) is used on the
élanSC400 microcontroller to select the ROMCS0
steering at system boot time. The boot ROM chip se-
lect (ROMCS0) can either be enabled to drive the
ROMCS0 pin or can be rerouted to drive the PC Card
(Socket A only) interface chip selects. The CFG0 and
CFG1 pins are still used to select the data bus width for
the ROMCS0 decode, regardless of the CFG2 config-
uration. The PC Card ROMCS0 redirection should not
be selected when the CFG0 and CFG1 configuration
pins are set to select a x32 ROM interface.
When the ROM chip select decode has been redi-
rected to PC Card Socket A, all of the normal PC Card
controller features can still be used to drive the PC
Card Socket A interface. The ROM chip select decode
remapping to the PC Card socket can be enabled and
disabled using firmware at any time.
Table 21.
Pinstrap Bus Buffer Options
CFG3
(
1
)
CFG1 CFG0
ROMCS0
Data
Width
x8
Reserved Reserved
x16
x32
2
x8
Reserved Reserved
x16
x32
2
DBUFOE
DBUFRDL
DBUFRDH
Disabled
R32BFOE
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
Disabled
Reserved
Disabled
Enabled
Disabled
Reserved
Disabled
Enabled
Disabled
Disabled
Enabled
Enabled
Enabled
Table 22.
CFG0 and CFG1 Configuration
CFG1
0
0
1
1
CFG0
0
1
0
1
Configuration
x8 ROMCS0 ROM interface
Reserved
x16 ROMCS0 ROM interface
x32 ROMCS0 ROM interface
Table 23.
CFG2 Configuration (élanSC400
microcontroller only)
CFG2
0
Configuration
Enables the ROMCS0 decode
on the ROMCS0 pin
Enables the ROMCS0 decode
to access PC Card Socket A
1
相關PDF資料 |
PDF描述 |
|---|---|
| ELANSC400-66AI | Single-Chip, Low-Power, PC/AT-Compatible Microcontrollers |
| ELANSC410-100AC | Single-Chip, Low-Power, PC/AT-Compatible Microcontrollers |
| ELANSC410-100AI | Single-Chip, Low-Power, PC/AT-Compatible Microcontrollers |
| ELANSC410-33AC | Single-Chip, Low-Power, PC/AT-Compatible Microcontrollers |
| ELANSC410-33AI | 5566-12BGS /N/MINI FIT CONN HOUS ASSY |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ELANSC400-66AI | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:Single-Chip, Low-Power, PC/AT-Compatible Microcontrollers |
| ELANSC400ANDELANSC410 | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:ElanSC400 and ElanSC410 - Single-Chip. Low-Power. PC/AT-Compatible Microcontrollers |
| ELANSC410 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:ElanSC410 - ElanSC410 Block Diagram |
| ELANSC410-100AC | 制造商:Advanced Micro Devices 功能描述:MCU 16-Bit/32-Bit Elan CISC ROMLess 3.3V 292-Pin BGA |
| ELANSC410-100ACAD | 制造商:Advanced Micro Devices 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。