- 您現在的位置：買賣IC網 > PDF目錄362614 > EK29 (Apex Microtechnology Corporation) POWER BOOSTER EVALUATION KIT PDF資料下載
參數資料
| 型號： | EK29 |
| 廠商： | Apex Microtechnology Corporation |
| 英文描述： | POWER BOOSTER EVALUATION KIT |
| 中文描述： | 功率增強評估板 |
| 文件頁數： | 1/3頁 |
| 文件大?。?/td> | 247K |
| 代理商： | EK29 |
APEX MICROTECHNOLOGY CORPORATION TELEPHONE (520) 690-8600 FAX (520) 888-3329 ORDERS (520) 690-8601 EMAIL prodlit@apexmicrotech.com
1
INTRODUCTION
This easy-to-use kit provides a platform for the evaluation of
the PB51 high voltage power boosters. The PB51 is designed
most commonly in combination with a small signal, general
purpose op amp. However, they can also be used without a
driver amplifier. This kit can be used to analyze a multitude of
standard or proprietary circuit configurations.
CAUTION
Use the supplied thermal washers or thermal
grease between the power amplifier and the
heat sink.
ASSEMBLY
1. On the silk screen side of the evaluation board, insert and
solder the MS06 mating socket in DUT holes 1-12. Be sure
each one is fully seated.
2. Solder components for your circuit. Be sure to incude proper
bypassing, required compensaton components and current
limit resistors. See the op amp data sheet for help in select-
ing these components.
3. Place the TW07 thermal washer on the heat sink over the
mounting hole for the DUT. Place a #6 screw through the
mounting hole and thread a #6 nut onto the screw at the back
of the heat sink. Do not tighten. Note that there are two sets
of mounting holes on the HS20. Holes on one edge allow
room between the DUT and evaluation board for the MS06
socket. The holes on the other edge are for direct through
hole mounting of the DUT to the evaluation board. It is rec-
ommended that you use the MS06.
4. Mount the DUT to the HS20 by sliding under the head of the
#6 screw and on top of the thermal washer. Tighten the nut
to the specified 8 to 10 in-lbs. (.9 to .13 N*M) do not over
torque.
5. Install leads of the DUT into the the MS06 on the evaluation
board. Use #6 self-tapping screws to secure the evalua-
tion board to the HS20 heatsink as shown in the assembly
diagram (Figure1).
PARTS LIST
Part #
HS20
EVAL30
MS06
TW07
BEFORE YOU GET STARTED
All Apex amplifiers should be handled using proper ESD
precautions.
Always use the heat sink and thermal washers included in
this kit.
Always use adequate power supply bypassing.
Do not change connections while the circuit is powered.
Initially set all power supplies to the minimum operating levels
allowed in the device data sheet.
Check for oscillations.
EQUIVALENT SCHEMATIC
Description
Heatsink
PC Board
Mating Socket
Thermal Washer
Quantity
1
1
1
1 package
相關PDF資料 |
PDF描述 |
|---|---|
| EK33 | EVALUATION KIT FOR PA75CX OR PA35CX PIN-OUT |
| EK57 | EVALUATION KIT FOR MP108FD & MP111FD PINUOT |
| EK60 | EVALUATION KIT FOR PA78 PIN-OUT |
| EK62 | EVALUATION KIT FOR SA305EX 3 PHASE BLDC MOTORDROVER |
| EKM6251 | U+P RF Mouse Rx Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EK29100-03 | 功能描述:EVAL BOARD FOR PE29100 制造商:peregrine semiconductor 系列:UltraCMOS? 零件狀態:在售 主要用途:電源管理，柵極驅動器 嵌入式:- 使用的 IC/零件:PE29100 主要屬性:板載測試點 輔助屬性:- 所含物品:板 標準包裝:1 |
| EK-29841-000 | 功能描述:麥克風 5.56 X 3.98 X 2.21MM -59 SENS, 9S PORT RoHS:否 制造商:Knowles Acoustics 方向性:Omnidirectional 阻抗:4.4 K Ohms 工作電壓:0.9 V to 10 V 靈敏度:- 53 dB 端接類型:Wire Leads 長度:5.56 mm 寬度:3.98 mm 深度:2.21 mm |
| EK-29842-049 | 功能描述:麥克風 5.56 X 3.98 X 2.21MM -55 SENS, 9S PORT RoHS:否 制造商:Knowles Acoustics 方向性:Omnidirectional 阻抗:4.4 K Ohms 工作電壓:0.9 V to 10 V 靈敏度:- 53 dB 端接類型:Wire Leads 長度:5.56 mm 寬度:3.98 mm 深度:2.21 mm |
| EK-29878-C05 | 功能描述:麥克風 5.56 X 3.98 X 2.21MM -53 SENS, 12S PORT RoHS:否 制造商:Knowles Acoustics 方向性:Omnidirectional 阻抗:4.4 K Ohms 工作電壓:0.9 V to 10 V 靈敏度:- 53 dB 端接類型:Wire Leads 長度:5.56 mm 寬度:3.98 mm 深度:2.21 mm |
| EK-29965-000 | 功能描述:麥克風 5.56 X 3.98 X 2.21MM 0 SENS, 12S PORT RoHS:否 制造商:Knowles Acoustics 方向性:Omnidirectional 阻抗:4.4 K Ohms 工作電壓:0.9 V to 10 V 靈敏度:- 53 dB 端接類型:Wire Leads 長度:5.56 mm 寬度:3.98 mm 深度:2.21 mm |
發布緊急采購，3分鐘左右您將得到回復。