- 您現在的位置：買賣IC網 > PDF目錄362614 > EK07 (Apex Microtechnology Corporation) EVALUATION KIT FOR SA07 PIN-OUT PDF資料下載
參數資料
| 型號： | EK07 |
| 廠商： | Apex Microtechnology Corporation |
| 英文描述： | EVALUATION KIT FOR SA07 PIN-OUT |
| 中文描述： | 評估板SA07引腳 |
| 文件頁數： | 1/4頁 |
| 文件大?。?/td> | 489K |
| 代理商： | EK07 |
APEX MICROTECHNOLOGY CORPORATION TELEPHONE (520) 690-8600 FAX (520) 888-3329 ORDERS (520) 690-8601 EMAIL prodlit@apexmicrotech.com
1
INTRODUCTION
This easy-to-use kit provides a platform for the evaluation
of PWM amplifier circuits using the SA07 pin-out. With ample
breadboarding areas it is flexible enough to analyze a multitude
of standard or proprietary circuit configurations. Critical con-
nections for power supply bypassing, compensation and current
limiting are pre-wired. Components not usually readily available
in engineering labs are provided. External connection to the
evaluation kit can be made via the terminals at the edge of the
circuit board. These terminal pads are suitable for standard
banana jacks or direct soldering of wires. The schematic is
shown in Figure 1.
PARTS LIST
Part #
Description, Vendor
CLAMP02
Mounting clip, Apex
HS21
Heat sink, Apex
EVAL18
PC Board, Apex
TWO9
Thermal washer, Apex
OX7R105KWN
Capacitor, Novacap
1825B105K201N
CRS01
Resistor, Caddock
MP725-0.10-1%
CRS02
Resistor, Caddock
MP725-0.05-1%
Quantity
1
1
1
1 Box/10 each
2
2
2
ASSEMBLY
See Figure 3.
1. Solder the surface mount ceramic capacitors to the DUT side
of the circuit board at CVs and CVcc.
2. Select a current limiting resistor from the two values provided.
See the product data sheet for information on how to select a
value. Apply a thin coating of thermal grease to the back of
the resistors. Press the resistor body onto the circuit board
foil at positions Ra and Rb and solder the leads.
3. Assemble the amplifier, thermal washer and heat sink to the
circuit board as illustrated in Figure 1. As a last step push
the clip through the heat sink and circuit board until it locks.
Solder the amplifier pins to the circuit side of the circuit
board.
4. The four holes at the corners of the circuit board are for
mounting #6 standoff spacers if desired.
5. Add other components as necessary to complete your ap-
plication circuit.
BEFORE YOU GET STARTED
* All Apex amplifiers should be handled using proper ESD
precautions.
* Always use thermal grease between the amplifier and heat-
sink.
* Always use adequate power supply bypassing.
* Do not change connections while the circuit is powered.
* Initially set all power supplies to the minimum operating levels
allowed in the device data sheet.
相關PDF資料 |
PDF描述 |
|---|---|
| EK11 | EVALUATION KIT FOR PA90, PA91, PA98 |
| EK15 | EVALUATION KIT FOR SA08 PIN-OUT |
| EK17 | EVALUATION KIT FOR SA12 PWM AMPLIFIER |
| EK21 | EVALUATION KIT FOR SA07 PIN-OUT |
| EK22 | EVALUATION KIT FOR PA94/PA95 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EK0710X05XA_D5X WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| EK0740X05XA_D5X WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| EK-0805AS-J | 功能描述:電感器套件及配件 0805 CASE 5% TOL 10 EACH-28 VALUES RoHS:否 制造商:Bourns 產品:SMD Inductor Kits 端接類型: 電感范圍: |
| EK0825X05XA-D5X WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| EK0880X25XA-D5X WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。