- 您現在的位置：買賣IC網 > PDF目錄362614 > EK01 (Apex Microtechnology Corporation) EVALUATION KIT FOR SA01 PIN-OUT PDF資料下載
參數資料
| 型號： | EK01 |
| 廠商： | Apex Microtechnology Corporation |
| 英文描述： | EVALUATION KIT FOR SA01 PIN-OUT |
| 中文描述： | 評估板SA01引腳 |
| 文件頁數： | 1/4頁 |
| 文件大?。?/td> | 247K |
| 代理商： | EK01 |
APEX MICROTECHNOLOGY CORPORATION TELEPHONE (520) 690-8600 FAX (520) 888-3329 ORDERS (520) 690-8601 EMAIL prodlit@apexmicrotech.com
1
INTRODUCTION
This easy-to-use kit provides a platform for the evaluation of
PWM amplifiers using the SA01 pin-out configuration. It can be
used to analyze a multitude of standard or proprietary circuit
configurations, and is flexible enough to do most standard
amplifier test configurations. The board is designed for surface
mounting all components except the switching amplifier.
The schematic is shown in Figure 2. Note that all of the
components shown on the schematic will probably not be used
for any single circuit. Some components will simply be omitted,
while others require installation of a jumper to complete the
signal path.
Only components unique to the EK01 are provided in this kit.
Hardware similar to that shown in figure 1 must be obtained lo-
cally. The PC board and the foot print of the heatsink measure
3" by 5".
PARTS LIST
Part #
Description
HS16
Heatsink
MS04
PC mount Cage Jacks
EVAL07
PC Board
60SPG00001
Spacer Grommets
TW10
Thermal Washer
BEFORE YOU GET STARTED
* All Apex amplifiers should be handled using proper ESD precautions.
* Always use the heatsink included in this kit with thermal grease.
* Torque the part to the specified 8 to 10 in-lbs (.9 to 1.13 N*M)
* Always use adequate power supply bypassing.
* Do not change connections while the circuit is powered.
* Initially set all power supplies to the minimum operating levels allowed in the device data sheet.
* Check for oscillations.
Quantity
1
1 Bag/12 each
1
4
1 Box/10 each
ASSEMBLY
1. From the non-silk screen side, insert and solder cage jacks.
Be sure each one is fully seated.
2. From the non-silk screen side, push spacer grommets into
PC board until fully seated. Grommets will snug when screws
are inserted for heatsink mounting.
3. Apply TW10 thermal washer or a thin, even coat of thermal
grease to the bottom of the SA01. If grease is from a tube
make sure there is no sign separation of solids and liquids.
If from a jar, stir it prior to application.
4. Use #14 sleeving to insulate and align at least 2 opposite
pins of the amplifier.
5. Mount amplifier to heatsink using #6 screws and nuts. Do
not over torque.
6. Install components as needed. External connections may be
soldered directly or standard banana jacks may be soldered
to these pads.
7. Insert amplifier pins into cage jacks and fasten board to
heatsink.
FIGURE 1.
相關PDF資料 |
PDF描述 |
|---|---|
| EK07 | EVALUATION KIT FOR SA07 PIN-OUT |
| EK11 | EVALUATION KIT FOR PA90, PA91, PA98 |
| EK15 | EVALUATION KIT FOR SA08 PIN-OUT |
| EK17 | EVALUATION KIT FOR SA12 PWM AMPLIFIER |
| EK21 | EVALUATION KIT FOR SA07 PIN-OUT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EK012 | 制造商:ALTECH 制造商全稱:Altech corporation 功能描述:Polycarbonate-130x94mm (5.12x3.70in.) |
| EK014AS014 | 制造商:Pervasive Displays Inc 功能描述:1.44" (V110) |
| EK0150X05XA_D5X WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| EK0160X25XA_D5X WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| EK02 | 制造商:SANKEN 制造商全稱:Sanken electric 功能描述:Schottky Barrier Diodes 20V |
發布緊急采購，3分鐘左右您將得到回復。