- 您現在的位置：買賣IC網 > PDF目錄362594 > EB9024 (Gennum Corporation) GENLINX-TM II EB9024 Evaluation Board PDF資料下載
參數資料
| 型號： | EB9024 |
| 廠商： | Gennum Corporation |
| 英文描述： | GENLINX-TM II EB9024 Evaluation Board |
| 中文描述： | GENLINX -商標二EB9024評估板 |
| 文件頁數： | 1/9頁 |
| 文件大小： | 123K |
| 代理商： | EB9024 |
PRELIMINARY
GENLINX
II
EB9024 Evaluation Board
EB9024 BLOCK DIAGRAM
Document No. VB2932 - 1
INTRODUCTION
The EB9024 is an evaluation and reference design platform
for the
GENLINX
II
GS9024 Equalizer and the GS9028
Cable Driver.
CIRCUIT DESCRIPTION
A functional block diagram is shown below and illustrates
the primary circuit functions. These include equalization
and driving 75
co-axial cables. A complete schematic is
also included.
The EB9024 accepts a serial digital data input signal
which first goes into the GS9024 equalizer. Equalization
of the input signal is completely automatic for signal
attenuation due to cable length from 0dB to in excess of
30dB. The signal strength/carrier detect output of the
equalizer, which is proportional to the amount of equalization
taking place, is available via test point TP1. Also available
as an output, is the equalizer "Output Eye Monitor" signal
via a SMA connector (J2). The signal strength/carrier
detect and Output Eye Monitor are useful diagnostic
outputs.
After equalization, the differential data signal is supplied
to the GS9028 cable driver which provides two
complementary data outputs at BNC connectors J3 and
J4. The GS9028 is configured to drive 75
co-axial
cables with SMPTE defined 800mV levels.
BOARD SET-UP AND TEST
The CD_ADJ input of the GS9024 is biased via a resistor
network including a potentiometer allowing the user to
adjust the level at which loss of carrier is detected. For a
detailed description of the CD_ADJ voltage level versus
muting threshold refer to the GS9024 data sheet. Turning
the potentiometer completely clockwise allows for maxi-
mum possible cable length equalization. In addition, the
GS9024 outputs can be put in a HIGH-Z state by putting
jumper JMP1 into the 1-2 position.
To verify operation of the EB9024, a source of serial digital
video should be applied to the input BNC connector using
75
co-axial cable. Using a signal source that is not
compliant to the SMPTE standards, can provide mislead-
ing results for equalizer cable length performance. The
output data stream is available at the serial output and can
be supplied to a D to A converter for verification via a
monitor. Note that jumper JMP1 must be in the 2-3 position
such that the equalizer outputs are enabled.
The power supply requirement for the EB9024 is +5V for
VCC at a current rating of 86mA (nominally).
PCB DETAILS
The EB9024 is a four layer printed circuit board con-
structed of standard FR-4 material and measures approxi-
mately 3.5" by 3.25". Ground and power plane layers are
internal to the board with signal layers on the top and
GS9024
EQUALIZER
SERIAL
DATA
INPUT
SERIAL
DATA
OUTPUTS
GS9028
CABLE
DRIVER
1
相關PDF資料 |
PDF描述 |
|---|---|
| EB9035 | GENLINX-TM II EB9035 Evaluation Board |
| EBO2 | TRIPLE INDEPENDENT LOGIC INTERFACED HALF BRIDGES |
| EC1086 | Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection |
| EC1086D | Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection |
| EC1086H | Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EB9035 | 制造商:GENNUM 制造商全稱:GENNUM 功能描述:GENLINX-TM II EB9035 Evaluation Board |
| EB91 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DOUBLE DIODE |
| EB9101 | 功能描述:放大器 IC 開發工具 RoHS:否 制造商:International Rectifier 產品:Demonstration Boards 類型:Power Amplifiers 工具用于評估:IR4302 工作電源電壓:13 V to 23 V |
| EB9131 | 制造商:ROCKWE 功能描述: |
| EB9479-000 | 制造商:TE Connectivity 功能描述:TXR40AZ90-1410BI - Bulk |
發布緊急采購，3分鐘左右您將得到回復。