- 您現在的位置：買賣IC網 > PDF目錄362594 > EB9035 (Gennum Corporation) GENLINX-TM II EB9035 Evaluation Board PDF資料下載
參數資料
| 型號： | EB9035 |
| 廠商： | Gennum Corporation |
| 英文描述： | GENLINX-TM II EB9035 Evaluation Board |
| 中文描述： | GENLINX -商標二EB9035評估板 |
| 文件頁數： | 1/9頁 |
| 文件大?。?/td> | 191K |
| 代理商： | EB9035 |
PRELIMINARY
GENLINX
II
EB9035 Evaluation Board
EB9035 BLOCK DIAGRAM
Document No. VB2931 -1
INTRODUCTION
The EB9035 is an evaluation and reference design platform
for the
GENLINX
II
GS9035 Reclocker and the GS9028
Cable Driver.
CIRCUIT DESCRIPTION
A functional block diagram is shown below and illustrates
the primary circuit functions. These include reclocking and
driving 75
co-axial cables. A complete schematic is also
included.
The EB9035 accepts differential serial digital data input
signals which go into the GS9035 reclocker. The reclocker
then generates clock and retimed data signals. In
addition, the complementary serial clock output signals
are available at BNC connectors J2 and J3. The GS9035
also drives data rate indication LEDs and a LOCK LED
which is provided to visually indicate when the reclocker
has locked to the incoming video signal.
The reclocked data signals are then supplied to the
GS9028 cable driver which provides two complementary
data outputs at BNC connectors J4 and J5. The GS9028
is configured to drive 75
co-axial cables with SMPTE
defined 800mV levels.
BOARD SET-UP AND TEST
The board is configured in SMPTE, auto-tune mode and
supports five data rates: 143Mb/s, 177Mb/s, 270Mb/s,
360Mb/s, and 540Mb/s. LED indicators are used to indicate
when the device is LOCKed and the detected data rate as
shown below.
SS2
0
0
0
0
1
SS1
0
0
1
1
0
SS0
0
1
0
1
0
143Mb/s
177Mb/s
270Mb/s
360Mb/s
540Mb/s
The GS9035 can also be configured for manual mode by
first putting the AUTO/MANUAL jumper (JMP1) into the 2-
3 position. Then jumpers JMP[7:5] are set accordingly.
Note that whenever the AUTO/MANUAL input of the GS9035
is HIGH (auto mode), jumpers JMP[7:5] should be left
floating to avoid bus contention.
To verify operation of the EB9035, a differential source of
serial digital video should be applied to the input BNC
connectors using 75
co-axial cable. A convenient differ-
ential source is available from the EB9024 evaluation
board. The output data stream is available at the serial
output and can be supplied to a D to A converter for
verification via a monitor. Note that the jumpers should be
set as shown below for an output to be present:
JMP1: 1-2 (reclocker configured for AUTO mode)
JMP2: 1-2 (reclocker configured for SMPTE mode)
SERIAL
DATA
OUTPUTS
GS9035
RECLOCKER
GS9028
CABLE
DRIVER
SERIAL
CLOCK
OUTPUTS
DIFFERENTIAL
SERIAL DATA
INPUTS
1
相關PDF資料 |
PDF描述 |
|---|---|
| EBO2 | TRIPLE INDEPENDENT LOGIC INTERFACED HALF BRIDGES |
| EC1086 | Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection |
| EC1086D | Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection |
| EC1086H | Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection |
| EC1086S | Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EB91 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DOUBLE DIODE |
| EB9101 | 功能描述:放大器 IC 開發工具 RoHS:否 制造商:International Rectifier 產品:Demonstration Boards 類型:Power Amplifiers 工具用于評估:IR4302 工作電源電壓:13 V to 23 V |
| EB9131 | 制造商:ROCKWE 功能描述: |
| EB9479-000 | 制造商:TE Connectivity 功能描述:TXR40AZ90-1410BI - Bulk |
| EB9689 | 功能描述:電源管理IC開發工具 Evaluation Board RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
發布緊急采購，3分鐘左右您將得到回復。