- 您現在的位置：買賣IC網 > PDF目錄97873 > E5561 e5561 Advance Information [Updated 4/03. 26 Pages] Read/Write transponder IC for contactless RF identification for highly sophisticated security applications. PDF資料下載
參數資料
| 型號： | E5561 |
| 英文描述： | e5561 Advance Information [Updated 4/03. 26 Pages] Read/Write transponder IC for contactless RF identification for highly sophisticated security applications. |
| 中文描述： | e5561推進信息[更新4 / 03。 26頁]讀/寫非接觸式射頻轉發器的高度復雜的安全應用識別芯片。 |
| 文件頁數： | 20/26頁 |
| 文件大?。?/td> | 410K |
| 代理商： | E5561 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁
3
e5561
4699A–RFID–04/03
Every section consists of one or more EEPROM blocks. Programming is carried out by
sending the programming data sequence to the e5561. When the base station sends
data to the transponder, this direction of data transmission will be designated as 'write'.
When the base station has sent the data sequence and the specified block has been
programmed, the e5561 transmits the content of the programmed EEPROM block. The
content is always sent in loop with terminator 1. The beginning of the data stream is indi-
cated by a preburst.
During programming, the e5561 monitors several fault and protection mechanisms. If a
fault or a protection violation is detected, the e5561 switches to ID mode.
Direct-access Mode
If the base station transmits a special data sequence to the e5561, it will enter the direct-
access mode. The base station can activate two different functions:
Read the content of a single block of the EEPROM
In this case, the e5561 transmits the block's content in loop, starting with a preburst
followed by the terminator which is also used to indicate the beginning of the trans-
mission of the specified block data.
Reset the e5561 in case of all modes
During direct-access mode, the e5561 monitors several fault and protection mecha-
nisms. If a fault or a protection violation is detected, the e5561 switches to ID mode.
Crypto Mode
In crypto mode, a non-linear high-security encryption algorithm called AUT64 is used to
authenticate the e5561.
After the base station has identified the e5561 (i.e., read the ID code), the base station
may authenticate the transponder by transmitting a challenge. Receiving this data
sequence causes the e5561 to switch to crypto mode.
This initiates the following actions:
While calculating the AUT64 result, the transponder transmits the checksum of the
challenge
The e5561 generates the response from the calculated result of the AUT64
As soon as the calculation is finished, the e5561 interrupts the transmission of the
checksum by sending a terminator
The e5561 transmits the response in loop with a terminator back to the base station
The base station can read the response and authentify the transponder. It is possible to
interrupt the calculation of the AUT64 result by sending another data sequence (e.g., if
the checksum was found to be wrong).
During crypto mode, the e5561 monitors several fault and protection mechanisms. If a
fault or a protection violation is detected, the e5561 enters ID mode.
Stop Mode
If two or more transponders are used simultaneously (e.g., in a manufacturing step), it
might be useful to be able to set the transponders to a passive state. To avoid a commu-
nication conflict, the base station has to transmit a special data sequence to the active
transponder(s) forcing them to switch to stop mode.
In stop mode, the e5561 switches off the damping as long as the RF field is applied.
After a power-on reset or after having received the software-reset command, the e5561
enters start-up and ID mode again.
During the data sequence of the stop mode, the e5561 monitors fault mechanisms. If a
fault is detected, the e5561 enters ID mode.
相關PDF資料 |
PDF描述 |
|---|---|
| E629-EDGE629 | 1 GHz Timing Deskew and Quad Fanout Element |
| E6420-EDGE6420 | Per-Pin Electronics Companion DAC |
| E646-EDGE646 | Pin Electronics Driver. Window Comparator. and Switch Matrix |
| E647-EDGE647 | Pin Electronics Driver. Window Comparator. and Switch Matrix |
| E649-EDGE649 | Octal Pin Electronics Driver / Receiver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| E5561_06 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Standard Read/Write Crypto Identification IC |
| e5561A-DOW | 功能描述:射頻無線雜項 Encryption w/unique options RoHS:否 制造商:Texas Instruments 工作頻率:112 kHz to 205 kHz 電源電壓-最大:3.6 V 電源電壓-最小:3 V 電源電流:8 mA 最大功率耗散: 工作溫度范圍:- 40 C to + 110 C 封裝 / 箱體:VQFN-48 封裝:Reel |
| E5562-00L022-L | 功能描述:以太網和電信連接器 RJ11 6P2C SIDE ENTRY RoHS:否 制造商:Pulse 產品:Modular Jacks 性能類別: USOC 代碼:RJ45 位置/觸點數量: 安裝風格:Through Hole 端口數量:1 x 1 型式:Female 屏蔽: 電流額定值: 電壓額定值: 觸點電鍍: 外殼材料:Thermoplastic IP 等級: |
| E5562-60L121-L | 功能描述:以太網和電信連接器 RJ11 6P2C SIDE ENTRY RoHS:否 制造商:Pulse 產品:Modular Jacks 性能類別: USOC 代碼:RJ45 位置/觸點數量: 安裝風格:Through Hole 端口數量:1 x 1 型式:Female 屏蔽: 電流額定值: 電壓額定值: 觸點電鍍: 外殼材料:Thermoplastic IP 等級: |
| E5562-60LU22-L | 功能描述:以太網和電信連接器 RJ11 6P2C SIDE ENTRY RoHS:否 制造商:Pulse 產品:Modular Jacks 性能類別: USOC 代碼:RJ45 位置/觸點數量: 安裝風格:Through Hole 端口數量:1 x 1 型式:Female 屏蔽: 電流額定值: 電壓額定值: 觸點電鍍: 外殼材料:Thermoplastic IP 等級: |
發布緊急采購，3分鐘左右您將得到回復。