參數資料
型號： E5561
英文描述： e5561 Advance Information [Updated 4/03. 26 Pages] Read/Write transponder IC for contactless RF identification for highly sophisticated security applications.
中文描述： e5561推進信息[更新4 / 03。 26頁]讀/寫非接觸式射頻轉發器的高度復雜的安全應用識別芯片。
文件頁數： 10/26頁
文件大?。?/td> 410K
代理商： E5561
18
e5561
4699A–RFID–04/03
For programming or direct-access mode, the password function has to be disabled by
receiving the password.
If this function is enabled, the customer configuration can only be changed by an autho-
rized person using the correct password of the e5561.
During password mode, the e5561 monitors several fault and protection mechanism. If a
fault or a protection violation is detected, the e5561 enters ID mode.
Error Handling
Several error conditions can be detected to ensure that only valid operations affect the
e5561.
Errors while Writing Data There are four detectable errors possible during writing data to the e5561:
Field gap was not detected
Wrong number of field clocks between two gaps, e.g., 37 FCs
The OPcode is not valid (11)
The number of bits received is incorrect; valid bit counts are:
–
programming mode: 38 bits
–
direct-access mode: 6 bits
–
crypto mode: 66 bits
–
stop mode: 2 bits
If any of these four conditions is detected, the e5561 stops writing and enters ID mode.
This can easily be analyzed using the damping which is usually on during writing. It
changes according to the selected modulation scheme in ID mode.
Errors During Programming
Mode
If the writing sequence has been transmitted successfully, there are three errors that
may prevent the e5561 from programming the data to the EEPROM:
The programming voltage VPP is too low, i.e., the field strength is not high enough
The lock-bit of the adressed block is set
The password function is enabled
In these cases, the procedure stops immediately after the error has been detected and
the IC reverts to ID mode.
Errors During Direct-access
Mode
In addition to the possible errors mentioned before, two errors may occur in direct-
access mode:
The lock-bit of the addressed block 5 to 8 is set
The password function is enabled
In these cases, the IC enters ID mode after the end of the writing sequence.
Errors During Crypto Mode
In crypto mode, ONE error mechanism is active, that may prevent the e5561 from send-
ing the correct response:
Error during the crypto writing sequence
The e5561 will enter ID mode immediately if an error in the writing sequence is detected.
If the password function is enabled, the e5561 enters ID mode after having completed
the writing sequence.
相關PDF資料
PDF描述
E629-EDGE629 1 GHz Timing Deskew and Quad Fanout Element
E6420-EDGE6420 Per-Pin Electronics Companion DAC
E646-EDGE646 Pin Electronics Driver. Window Comparator. and Switch Matrix
E647-EDGE647 Pin Electronics Driver. Window Comparator. and Switch Matrix
E649-EDGE649 Octal Pin Electronics Driver / Receiver
相關代理商/技術參數
參數描述
E5561_06 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Standard Read/Write Crypto Identification IC
e5561A-DOW 功能描述:射頻無線雜項 Encryption w/unique options RoHS:否 制造商:Texas Instruments 工作頻率:112 kHz to 205 kHz 電源電壓-最大:3.6 V 電源電壓-最小:3 V 電源電流:8 mA 最大功率耗散: 工作溫度范圍:- 40 C to + 110 C 封裝 / 箱體:VQFN-48 封裝:Reel
E5562-00L022-L 功能描述:以太網和電信連接器 RJ11 6P2C SIDE ENTRY RoHS:否 制造商:Pulse 產品:Modular Jacks 性能類別: USOC 代碼:RJ45 位置/觸點數量: 安裝風格:Through Hole 端口數量:1 x 1 型式:Female 屏蔽: 電流額定值: 電壓額定值: 觸點電鍍: 外殼材料:Thermoplastic IP 等級:
E5562-60L121-L 功能描述:以太網和電信連接器 RJ11 6P2C SIDE ENTRY RoHS:否 制造商:Pulse 產品:Modular Jacks 性能類別: USOC 代碼:RJ45 位置/觸點數量: 安裝風格:Through Hole 端口數量:1 x 1 型式:Female 屏蔽: 電流額定值: 電壓額定值: 觸點電鍍: 外殼材料:Thermoplastic IP 等級:
E5562-60LU22-L 功能描述:以太網和電信連接器 RJ11 6P2C SIDE ENTRY RoHS:否 制造商:Pulse 產品:Modular Jacks 性能類別: USOC 代碼:RJ45 位置/觸點數量: 安裝風格:Through Hole 端口數量:1 x 1 型式:Female 屏蔽: 電流額定值: 電壓額定值: 觸點電鍍: 外殼材料:Thermoplastic IP 等級:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*