參數資料
型號: DSPIC33FJ128GP708-I/PT
廠商: Microchip Technology
文件頁數: 14/90頁
文件大?。?/td> 0K
描述: IC DSPIC MCU/DSP 128K 80TQFP
產品培訓模塊: Introduction to dsPIC33F Architecture Part 1
Asynchronous Stimulus
Introduction to dsPIC33F Architecture Part 2
特色產品: PIC24FJ/33FJ MCUs & dsPIC? DSCs
標準包裝: 119
系列: dsPIC™ 33F
核心處理器: dsPIC
芯體尺寸: 16-位
速度: 40 MIP
連通性: CAN,I²C,IrDA,LIN,SPI,UART/USART
外圍設備: AC'97,欠壓檢測/復位,DMA,I²S,POR,PWM,WDT
輸入/輸出數: 69
程序存儲器容量: 128KB(128K x 8)
程序存儲器類型: 閃存
RAM 容量: 16K x 8
電壓 - 電源 (Vcc/Vdd): 3 V ~ 3.6 V
數據轉換器: A/D 24x10b/12b
振蕩器型: 內部
工作溫度: -40°C ~ 85°C
封裝/外殼: 80-TQFP
包裝: 托盤
產品目錄頁面: 654 (CN2011-ZH PDF)
配用: 876-1001-ND - DSPIC33 BREAKOUT BOARD
DM300024-ND - KIT DEMO DSPICDEM 1.1
DV164033-ND - KIT START EXPLORER 16 MPLAB ICD2
MA330012-ND - MODULE DSPIC33 100P TO 84QFP
MA330011-ND - MODULE DSPIC33 100P TO 100QFP
DM300019-ND - BOARD DEMO DSPICDEM 80L STARTER
DM240001-ND - BOARD DEMO PIC24/DSPIC33/PIC32
AC164328-ND - MODULE SKT FOR 80TQFP
DV164005-ND - KIT ICD2 SIMPLE SUIT W/USB CABLE
2005 Microchip Technology Inc.
Preliminary
DS70155C-page 19
dsPIC33F
6.0
SYSTEM INTEGRATION
System
management
services
provided
by
the
dsPIC33F device family include:
Control of clock options and oscillators
Power-on Reset
Oscillator Start-up Timer/Stabilizer
Watchdog Timer with RC oscillator
Fail-Safe Clock Monitor
Reset by multiple sources
6.1
Clock Options and Oscillators
There are 7 clock options provided by the dsPIC33F:
FRC Oscillator
FRC Oscillator with PLL
Primary (XT, HS or EC) Oscillator
Primary Oscillator with PLL
Secondary (LP) Oscillator
LPRC Oscillator
The FRC (Fast RC) internal oscillator runs at a nominal
frequency of 7.37 MHz. The user software can tune the
FRC frequency. User software can specify a factor by
which this clock frequency is scaled.
The primary oscillator can use one of the following as
its clock source:
1.
XT (Crystal): Crystals and ceramic resonators in
the range of 3 MHz to 10 MHz. The crystal is
connected to the OSC1 and OSC2 pins.
2.
HS (High-Speed Crystal): Crystals in the range
of 10 MHz to 40 MHz. The crystal is connected
to the OSC1 and OSC2 pins.
3.
EC (External Clock): External clock signal in the
range of 0.8 MHz to 64 MHz. The external clock
signal is directly applied to the OSC1 pin.
The secondary (LP) oscillator is designed for low power
and uses a 32 kHz crystal or ceramic resonator. The LP
oscillator uses the SOSCI and SOSCO pins.
The LPRC (Low-Power RC) internal oscIllator runs at a
nominal frequency of 32.768 kHz. Another scaled
reference clock is used by the Watchdog Timer (WDT)
and Fail-Safe Clock Monitor (FSCM).
The clock signals generated by the FRC and primary
oscillators can be optionally applied to an on-chip
Phase Locked Loop (PLL) to provide a wide range of
output frequencies for device operation. The input to
the PLL can be in the range of 1.6 MHz to 16 MHz, and
the PLL Phase Detector Input Divider, PLL Multiplier
Ratio and PLL Voltage Controlled Oscillator (VCO) can
be individually configured by user software to generate
output frequencies in the range of 25 MHz to 160 MHz.
The output of the oscillator (or the output of the PLL if
a PLL mode has been selected) is divided by 4 to
generate the device instruction clock (FCY). FCY
defines the operating speed of the device, and speeds
up to 40 MHz are supported by the dsPIC33F
architecture.
The dsPIC33F oscillator system provides:
Various external and internal oscillator options as
clock sources
An on-chip PLL to scale the internal operating
frequency to the required system clock frequency
The internal FRC oscillator can also be used with
the PLL, thereby allowing full-speed operation
without any external clock generation hardware
Clock switching between various clock sources
Programmable clock postscaler for system power
savings
A Fail-Safe Clock Monitor (FSCM) that detects
clock failure and takes fail-safe measures
A Clock Control register (OSCCON)
Nonvolatile configuration bits for main oscillator
selection.
A simplified block diagram of the oscillator system is
shown in Figure 6-1.
相關PDF資料
PDF描述
DSPIC33FJ64MC510A-I/PF IC DSPIC MCU/DSP 64K 100-TQFP
PIC18LF4620-I/PT IC MCU FLASH 32KX16 44TQFP
PIC32MX664F128H-I/MR MCU PIC 128KB FLASH 64QFN
DSPIC33FJ256GP510-I/PT IC DSPIC MCU/DSP 256K 100TQFP
PIC24HJ128GP510-I/PF IC PIC MCU FLASH 128KB 100TQFP
相關代理商/技術參數
參數描述
dsPIC33FJ128GP708T-I/PT 功能描述:數字信號處理器和控制器 - DSP, DSC 40MIPS 128KB RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
dsPIC33FJ128GP710A-E/PF 功能描述:數字信號處理器和控制器 - DSP, DSC 16Bit MCU/DSP 40MIPS 128KB FLASH RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
dsPIC33FJ128GP710A-E/PT 功能描述:數字信號處理器和控制器 - DSP, DSC 16Bit 40MIPS 128KB Flash RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
dsPIC33FJ128GP710A-H/PF 功能描述:數字信號處理器和控制器 - DSP, DSC 16 bit DSC 20MIPS 128KB Flash RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
dsPIC33FJ128GP710A-H/PT 功能描述:數字信號處理器和控制器 - DSP, DSC 16 bit DSC 20MIPS 128KB Flash RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT