參數資料
型號： DSPIC30F6010T-20E/PF
廠商： Microchip Technology
文件頁數： 28/66頁
文件大?。?/td> 0K
描述： IC PSPIC MCU/DSP 144K 80TQFP
產品培訓模塊： Asynchronous Stimulus
標準包裝： 1,000
系列： dsPIC™ 30F
核心處理器： dsPIC
芯體尺寸： 16-位
速度： 20 MIPS
連通性： CAN，I²C，SPI，UART/USART
外圍設備： 高級欠壓探測/復位，LVD，電機控制 PWM，QEI，POR，PWM，WDT
輸入/輸出數： 68
程序存儲器容量： 144KB（48K x 24）
程序存儲器類型： 閃存
EEPROM 大小： 4K x 8
RAM 容量： 8K x 8
電壓 - 電源 (Vcc/Vdd)： 2.5 V ~ 5.5 V
數據轉換器： A/D 16x10b
振蕩器型： 內部
工作溫度： -40°C ~ 125°C
封裝/外殼： 80-TQFP
包裝： 帶卷 (TR)
配用： DM300019-ND - BOARD DEMO DSPICDEM 80L STARTER
AC164314-ND - MODULE SKT FOR PM3 80PF
DM300020-ND - BOARD DEV DSPICDEM MC1 MOTORCTRL
其它名稱： DSPIC30F6010T20EP
dsPIC30F Flash Programming Specification
DS70102K-page 34
2010 Microchip Technology Inc.
11.0 ICSP MODE
11.1
ICSP Mode
ICSP mode is a special programming protocol that
allows you to read and write to the dsPIC30F program-
ming executive. The ICSP mode is the second (and
slower) method used to program the device. This mode
also has the ability to read the contents of executive
memory to determine whether the programming exec-
utive is present. This capability is accomplished by
applying control codes and instructions serially to the
device using pins PGC and PGD.
In ICSP mode, the system clock is taken from the PGC
pin, regardless of the device’s oscillator Configuration
bits. All instructions are first shifted serially into an
internal buffer, then loaded into the Instruction register
and executed. No program fetching occurs from
internal memory. Instructions are fed in 24 bits at a
time. PGD is used to shift data in and PGC is used as
both the serial shift clock and the CPU execution clock.
Data is transmitted on the rising edge and latched on
the falling edge of PGC. For all data transmissions, the
Least Significant bit (LSb) is transmitted first.
11.2
ICSP Operation
Upon entry into ICSP mode, the CPU is idle. Execution
of the CPU is governed by an internal state machine. A
4-bit control code is clocked in using PGC and PGD,
and this control code is used to command the CPU
(see Table 11-1).
The SIX control code is used to send instructions to the
CPU for execution, while the REGOUT control code is
used to read data out of the device via the VISI register.
The operation details of ICSP mode are provided in
TABLE 11-1:
CPU CONTROL CODES IN
ICSP MODE
4-bit
Control
Code
Mnemonic
Description
0000b
SIX
Shift in 24-bit instruction
and execute.
0001b
REGOUT
Shift out the VISI
register.
0010b-1111b N/A
Reserved.
11.2.1
SIX SERIAL INSTRUCTION
EXECUTION
The SIX control code allows execution of dsPIC30F
assembly instructions. When the SIX code is received,
the CPU is suspended for 24 clock cycles as the
instruction is then clocked into the internal buffer. Once
the instruction is shifted in, the state machine allows it
to be executed over the next four clock cycles. While
the received instruction is executed, the state machine
simultaneously shifts in the next 4-bit command (see
Note 1: During ICSP operation, the operating
frequency of PGC must not exceed
5 MHz.
2: Because ICSP is slower, it is recom-
mended that only Enhanced ICSP (E-
ICSP) mode be used for device program-
ming, as described in Section 5.1
Note 1: Coming out of the ICSP entry sequence,
the first 4-bit control code is always
forced to SIX and a forced NOP instruc-
tion is executed by the CPU. Five addi-
tional PGC clocks are needed on start-
up, thereby resulting in a 9-bit SIX com-
mand instead of the normal 4-bit SIX
command. After the forced SIX is clocked
in, ICSP operation resumes as normal
(the next 24 clock cycles load the first
instruction word to the CPU). See
Figure 11-1 for details.
2: TBLRDH, TBLRDL, TBLWTH and TBLWTL
instructions must be followed by a NOP
instruction.
相關PDF資料
PDF描述
DSPIC30F4013T-20I/PT IC DSPIC MCU/DSP 48K 44TQFP
DSPIC30F4013T-20I/ML IC DSPIC MCU/DSP 48K 44QFN
DSPIC30F4012T-20I/SO IC DSPIC MCU/DSP 48K 28SOIC
DSPIC30F4012T-20I/ML IC DSPIC MCU/DSP 48K 44QFN
PIC24F16KL402-I/SO IC MCU 16BIT 16KB FLASH 28-SOIC
相關代理商/技術參數
參數描述
DSPIC30F6010T-20I/PF 功能描述:數字信號處理器和控制器 - DSP, DSC 20MHz 144KB Flash RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
DSPIC30F6010T-30I/PF 功能描述:數字信號處理器和控制器 - DSP, DSC 30MHz 144KB Flash RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
DSPIC30F6011-20E/PF 功能描述:數字信號處理器和控制器 - DSP, DSC 30MHz 144KB Flash RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
DSPIC30F6011-20I/PF 功能描述:數字信號處理器和控制器 - DSP, DSC 20MHz 132KB Flash RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
DSPIC30F6011-20I/PF 制造商:Microchip Technology Inc 功能描述:16BIT 20MIPS DSPIC SMD 30F6011
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*