參數資料
型號： DSPIC30F2020-20E/MM
廠商： Microchip Technology
文件頁數： 31/66頁
文件大?。?/td> 0K
描述： IC DSPIC MCU/DSP 12K 28QFN
產品培訓模塊： Asynchronous Stimulus
特色產品： SMPS & Digital Power Conversion Solutions
標準包裝： 61
系列： dsPIC™ 30F
核心處理器： dsPIC
芯體尺寸： 16-位
速度： 20 MIPS
連通性： I²C，IrDA，LIN，SPI，UART/USART
外圍設備： 欠壓檢測/復位，POR，PWM，WDT
輸入/輸出數： 21
程序存儲器容量： 12KB（4K x 24）
程序存儲器類型： 閃存
RAM 容量： 512 x 8
電壓 - 電源 (Vcc/Vdd)： 3 V ~ 5.5 V
數據轉換器： A/D 8x10b
振蕩器型： 內部
工作溫度： -40°C ~ 125°C
封裝/外殼： 28-VQFN 裸露焊盤
包裝： 管件
產品目錄頁面： 650 (CN2011-ZH PDF)
配用： DM300023-ND - KIT DEMO DSPICDEM SMPS BUCK
AC164322-ND - MODULE SOCKET MPLAB PM3 28/44QFN
DV164005-ND - KIT ICD2 SIMPLE SUIT W/USB CABLE
2010 Microchip Technology Inc.
DS70102K-page 37
dsPIC30F Flash Programming Specification
11.4
Flash Memory Programming in
ICSP Mode
Programming in ICSP mode is described in
ming Cycle”. Step-by-step procedures are described
operations must use serial execution, as described in
11.4.1
PROGRAMMING OPERATIONS
Flash memory write and erase operations are
controlled by the NVMCON register. Programming is
performed by setting NVMCON to select the type of
erase operation (Table 11-2) or write operation
(Table 11-3), writing a key sequence to enable the
programming and initiating the programming by setting
the WR control bit, NVMCON<15>.
In ICSP mode, all programming operations are
externally timed. An external 2 ms delay must be used
between setting the WR control bit and clearing the WR
control bit to complete the programming operation.
TABLE 11-2:
NVMCON ERASE
OPERATIONS
NVMCON
Value
Erase Operation
0x407F
Erase all code memory, data memory
(does not erase UNIT ID).
0x4075
Erase 1 row (16 words) of data
EEPROM.
0x4074
Erase 1 word of data EEPROM.
0x4072
Erase all executive memory.
0x4071
Erase 1 row (32 instruction words)
from 1 panel of code memory.
0x406E
Erase Boot Secure and General
Segments, then erase FBS, FSS and
FGS configuration registers.
0x4066
Erase all Data EEPROM allocated to
Boot Segment.
0x405E
Erase Secure and General Segments,
then erase FSS and FGS configuration
registers.
0x4056
Erase all Data EEPROM allocated to
Secure Segment.
0x404E
Erase General Segment, then erase
FGS configuration register.
0x4046
Erase all Data EEPROM allocated to
General Segment.
TABLE 11-3:
NVMCON WRITE
OPERATIONS
NVMCON
Value
Write Operation
0x4008
Write 1 word to configuration
memory.
0x4005
Write 1 row (16 words) to data memory.
0x4004
Write 1 word to data memory.
0x4001
Write 1 row (32 instruction words) into
1 panel of program memory.
11.4.2
UNLOCKING NVMCON FOR
PROGRAMMING
Writes to the WR bit (NVMCON<15>) are locked to
prevent accidental programming from taking place.
Writing a key sequence to the NVMKEY register
unlocks the WR bit and allows it to be written to. The
unlock sequence is performed as follows:
MOV
#0x55, W8
MOV
W8, NVMKEY
MOV
#0xAA, W9
MOV
W9, NVMKEY
Note:
Any working register, or working register
pair, can be used to write the unlock
sequence.
11.4.3
STARTING AND STOPPING A
PROGRAMMING CYCLE
Once the unlock key sequence has been written to the
NVMKEY register, the WR bit (NVMCON<15>) is used
to start and stop an erase or write cycle. Setting the WR
bit initiates the programming cycle. Clearing the WR bit
terminates the programming cycle.
All erase and write cycles must be externally timed. An
external delay must be used between setting and
clearing the WR bit. Starting and stopping a
programming cycle is performed as follows:
BSET
NVMCON, #WR
<Wait 2 ms>
BCLR
NVMCON, #WR
11.5
Erasing Program Memory in
Normal-Voltage Systems
The procedure for erasing program memory (all code
memory, data memory, executive memory and code-
protect bits) consists of setting NVMCON to 0x407F,
unlocking NVMCON for erasing and then executing the
programming cycle. This method of bulk erasing pro-
gram memory only works for systems where VDD is
between 4.5 volts and 5.5 volts. The method for erasing
program memory for systems with a lower VDD (3.0
volts-4.5 volts) is described in Section 6.1 “Erasing
相關PDF資料
PDF描述
ATTINY13V-10SSI IC MCU AVR 1K FLASH 10MHZ 8SOIC
ATTINY13V-10SI IC MCU AVR 1K FLASH 10MHZ 8SOIC
ATTINY13V-10PI IC MCU AVR 1K FLASH 10MHZ 8DIP
ATTINY13-20SSI IC MCU AVR 1K FLASH 20MHZ 8SOIC
ATTINY13-20SI IC MCU AVR 1K FLASH 20MHZ 8SOIC
相關代理商/技術參數
參數描述
dsPIC30F2020-30I/MM 功能描述:數字信號處理器和控制器 - DSP, DSC 12KB 512bytes-RAM 30MIPS 21I/O RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
DSPIC30F2020-30I/MMB32 功能描述:IC DSPIC MCU/DSP 12K 28QFN RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:dsPIC™ 30F 產品培訓模塊:The Ultra-Low Power MSP430 MSP430 Overview MSP430 Design Tools MSP430 Peripherals MSP430 for Utility Metering Solutions MSP430: How to JTAG MSP430, How To Use the Clock System Grace Software Graphical User Interface MCU Overview Driver Library MSP430Ware Overview 標準包裝:60 系列:MSP430F2xx 核心處理器:RISC 芯體尺寸:16-位 速度:12MHz 連通性:SPI，UART/USART 外圍設備:欠壓檢測/復位，PWM，WDT 輸入/輸出數:11 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:256 x 8 電壓 - 電源 (Vcc/Vdd):1.8 V ~ 3.6 V 數據轉換器:A/D 3x24b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:24-TSSOP（0.173"，4.40mm 寬） 包裝:管件
dsPIC30F2020-30I/SO 功能描述:數字信號處理器和控制器 - DSP, DSC 12KB 512bytes-RAM 30MIPS 21I/O RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
dsPIC30F2020-30I/SP 功能描述:數字信號處理器和控制器 - DSP, DSC 12KB 512bytes-RAM 30MIPS 21I/O RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
DSPIC30F2020AT-20E 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:28/44-Pin High-Performance Switch Mode Power Supply Digital Signal Controllers
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*