- 您現在的位置：買賣IC網 > PDF目錄377002 > DSPCOMMANDUM Universal Command Converter for DSP User＇s Manual PDF資料下載
參數資料
| 型號： | DSPCOMMANDUM |
| 英文描述： | Universal Command Converter for DSP User＇s Manual |
| 中文描述： | 通用命令轉換為數字信號處理器用戶手冊 |
| 文件頁數： | 33/70頁 |
| 文件大小： | 550K |
| 代理商： | DSPCOMMANDUM |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁當前第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁
Motorola
Functional Description
3-1
Chapter 3
Functional Description
The application development system (ADS) user interacts with the target DSP through
two subsystem components, the host computer interface and the command converter
controller. The host computer interface consists of a program written in the C language
that interacts with a host computer bus interface card. The command converter consists of
a program written in DSP56002 assembly language which interacts with the host
computer bus interface card and the target JTAG/OnCE port.
It should be noted that older versions of Motorola DSP products use the OnCE port
protocol, while newer versions of Motorola DSP products use the IEEE JTAG 4-wire
protocol to interact with their OnCE port. New versions of the command converter support
both JTAG and OnCE protocols.
Commands entered from the host computer’s keyboard are parsed and a series of low level
command packets are sent to the command converter. The command converter translates
these low level command packets into serial sequences that are transferred to the target
DSP via its JTAG/OnCE port. The JTAG/OnCE port provides the necessary control to the
target so programs may be loaded or saved, registers read or modified, and hardware
breakpoints set or cleared.
The host computer interface is designed to communicate with as many as eight command
converter cards. This requires a special software protocol to avoid data collisions between
one target and another. The purpose of this section is to describe the subsystem
components of the ADS to give a better understanding of the communication link between
the user and the target DSP.
3.1 Host Computer Hardware
The host computer’s hardware interface provides the communications link between the
user and the command converter. The ADS user interface program uses a software
handshake when communicating with the command converter. There are signals defined
on the host computer bus interface card which are used for requesting and acknowledging
information transfer. Since the handshake is software driven the transfer rate will be
相關PDF資料 |
PDF描述 |
|---|---|
| DSPCOMMPARALLELUM | Parallel Port Command Converter for DSP User＇s Manual |
| DSPCOMMPCIUM | PCI Command Converter for DSP User＇s Manual |
| DSPG4001-71 | Telecommunication IC |
| DSPG5002 | Analog IC |
| DSPG5003 | Analog IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DSPCOMMPARALLEL | 功能描述:程序設計器配件 PARALLEL COMMAND CONV RoHS:否 制造商:Lattice 產品:ispDOWNLOAD Cables 用于:In-system Programming |
| DSPCOMMPARALLELE | 功能描述:界面開發工具 PARALLEL COMMAND CONV RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| DSPCOMMPARALLELE | 制造商:Freescale Semiconductor 功能描述:PARALLEL COMMAND CONV |
| DSPCOMMPARALLELUM | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Parallel Port Command Converter for DSP User＇s Manual |
| DSPCOMMPCIUM | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:PCI Command Converter for DSP User＇s Manual |
發布緊急采購，3分鐘左右您將得到回復。