參數資料
型號: DSP56321VL200
廠商: Freescale Semiconductor
文件頁數: 9/84頁
文件大?。?/td> 0K
描述: IC DSP 24BIT 200MHZ 196-MAPBGA
標準包裝: 126
系列: DSP56K/Symphony
類型: 定點
接口: 主機接口,SSI,SCI
時鐘速率: 200MHz
非易失內存: ROM(576 B)
芯片上RAM: 576kB
電壓 - 輸入/輸出: 3.30V
電壓 - 核心: 1.60V
工作溫度: -40°C ~ 100°C
安裝類型: 表面貼裝
封裝/外殼: 196-FBGA
供應商設備封裝: 196-MAPBGA(15x15)
包裝: 托盤
Enhanced Synchronous Serial Interface 1 (ESSI1)
DSP56321 Technical Data, Rev. 11
Freescale Semiconductor
1-11
1.8 Enhanced Synchronous Serial Interface 1 (ESSI1)
STD0
PC5
Output
Input or Output
Ignored Input
Serial Transmit Data—Transmits data from the Serial Transmit Shift Register.
STD0 is an output when data is transmitted.
Port C 5—The default configuration following reset is GPIO input PC5. When
configured as PC5, signal direction is controlled through the Port C Direction
Register. The signal can be configured as an ESSI signal STD0 through the Port
C Control Register.
Notes:
1.
In the Stop state, the signal maintains the last state as follows:
If the last state is input, the signal is an ignored input.
If the last state is output, these lines have weak keepers that maintain the last output state even if the drivers are tri-stated.
2.
The Wait processing state does not affect the signal state.
Table 1-12.
Enhanced Serial Synchronous Interface 1
Signal Name
Type
State During
Reset1,2
Signal Description
SC10
PD0
Input or Output
Ignored Input
Serial Control 0—For asynchronous mode, this signal is used for the receive
clock I/O (Schmitt-trigger input). For synchronous mode, this signal is used
either for transmitter 1 output or for serial I/O flag 0.
Port D 0—The default configuration following reset is GPIO input PD0. When
configured as PD0, signal direction is controlled through the Port D Direction
Register. The signal can be configured as an ESSI signal SC10 through the Port
D Control Register.
SC11
PD1
Input/Output
Input or Output
Ignored Input
Serial Control 1—For asynchronous mode, this signal is the receiver frame
sync I/O. For synchronous mode, this signal is used either for Transmitter 2
output or for Serial I/O Flag 1.
Port D 1—The default configuration following reset is GPIO input PD1. When
configured as PD1, signal direction is controlled through the Port D Direction
Register. The signal can be configured as an ESSI signal SC11 through the Port
D Control Register.
SC12
PD2
Input/Output
Input or Output
Ignored Input
Serial Control Signal 2—The frame sync for both the transmitter and receiver
in synchronous mode and for the transmitter only in asynchronous mode. When
configured as an output, this signal is the internally generated frame sync signal.
When configured as an input, this signal receives an external frame sync signal
for the transmitter (and the receiver in synchronous operation).
Port D 2—The default configuration following reset is GPIO input PD2. When
configured as PD2, signal direction is controlled through the Port D Direction
Register. The signal can be configured as an ESSI signal SC12 through the Port
D Control Register.
Table 1-11.
Enhanced Synchronous Serial Interface 0 (Continued)
Signal Name
Type
State During
Reset1,2
Signal Description
相關PDF資料
PDF描述
AGM30DRSN-S288 CONN EDGECARD EXTEND 60POS .156
IRS2168DPBF IC PFC BALLAST CTLR ADV 16-PDIP
EP4CE6F17I8LN IC CYCLONE IV E FPGA 6K 256FBGA
T525D227M004ATE025 CAP TANT 220UF 4V 20% 2917
TPSD686M016R0150 CAP TANT 68UF 16V 20% 2917
相關代理商/技術參數
參數描述
DSP56321VL200R2 功能描述:數字信號處理器和控制器 - DSP, DSC 24 BIT DSP PBFREE RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
DSP56321VL220 功能描述:數字信號處理器和控制器 - DSP, DSC 24 BIT DSP PBFREE RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
DSP56321VL240 功能描述:數字信號處理器和控制器 - DSP, DSC 24 BIT DSP PBFREE RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
DSP56321VL275 功能描述:數字信號處理器和控制器 - DSP, DSC 24 BIT DSP PBFREE RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
DSP56321VL275 制造商:Freescale Semiconductor 功能描述:Digital Signal Processor (DSP) IC