參數資料
型號： DS80C390-QNR
廠商： DALLAS SEMICONDUCTOR
元件分類： Microcontroller
英文描述： 8-BIT, 40 MHz, MICROCONTROLLER, PQCC68
封裝： PLASTIC, LCC-68
文件頁數： 34/58頁
文件大?。?/td> 5486K
代理商： DS80C390-QNR
DS80C390
4 of 58
110199
PIN DESCRIPTION Table 1
LQFP
PLCC
SIGNAL
NAME
DESCRIPTION
8, 22,
40, 56
17, 32,
51, 68
VCC
+5V
9, 25,
41, 57
1, 18,
35, 52
GND
Digital Circuit Ground
46
57
ALE
Address Latch Enable - Output. When the MUX pin is low, this
pin outputs a clock to latch the external address LSB from the
multiplexed address/data bus on Port 0. This signal is commonly
connected to the latch enable of an external transparent latch. ALE
has a pulse width of 1.5 XTAL1 cycles and a period of four
XTAL1 cycles. When the MUX pin is high, the pin will toggle
continuously if the ALEOFF bit is cleared.
ALE is forced high
when the device is in a Reset condition or if the ALEOFF bit is set
while the MUX pin is high.
45
56
PSEN
Program Store Enable - Output. This signal is the chip enable for
external ROM memory. PSEN provides an active low pulse and is
driven high when external ROM is not being accessed.
47
58
EA
External Access Enable - Input. This pin must be tied to GND for
proper operation.
26
36
MUX
Multiplex/Demultiplex Select - Input.
This pin selects if the
address/data
bus
operates
in
multiplexed
( MUX =0)
or
demultiplexed ( MUX =1) mode.
2
11
RST
Reset - Input. The RST input pin contains a Schmitt voltage input
to recognize external active high Reset inputs.
The pin also
employs an internal pulldown resistor to allow for a combination of
wired OR external Reset sources. An RC circuit is not required for
power-up, as the device provides this function internally.
3
12
RSTOL
Reset Output Low- Output. This active low signal will be
asserted:
When the processor has entered reset via the RST pin,
During crystal warm-up period following power-on or Stop mode,
During a watchdog timer reset (2 cycles duration),
During an oscillator failure (if OFDE=1),
Whenever VCC
≤ V
RST
23,
24
33,
34
XTAL2,
XTAL1
XTAL1, XTAL2 - Crystal oscillator pins support fundamental
mode, parallel resonant, AT cut crystals. XTAL1 is the input if an
external clock source is used in place of a crystal. XTAL2 is the
output of the crystal amplifier.
55
54
53
52
51
50
49
48
67
66
65
64
63
62
61
59
AD0 / D0
AD1 / D1
AD2 / D2
AD3 / D3
AD4 / D4
AD5 / D5
AD6 / D6
AD7 / D7
AD0-7 (Port 0) - I/O. When the MUX pin is tied low, Port 0 is the
multiplexed address/data bus. While ALE is high, the LSB of a
memory address is presented. While ALE falls, the port transitions
to a bi-directional data bus. When the MUX pin is tied high, Port 0
functions as the bi-directional data bus. Port 0 cannot be modified
by software. The reset condition of Port 0 pins is high. No pullup
resistors are needed.
相關PDF資料
PDF描述
DS80C390-FNR 8-BIT, 40 MHz, MICROCONTROLLER, PQFP64
DS80CH11 8-BIT, MICROCONTROLLER, PQFP128
DS83C530-ENL 8-BIT, OTPROM, 33 MHz, MICROCONTROLLER, PQFP52
DS87C530-ECL 8-BIT, OTPROM, 33 MHz, MICROCONTROLLER, PQFP52
DS87C520-MCL 8-BIT, OTPROM, MICROCONTROLLER, PDIP40
相關代理商/技術參數
參數描述
DS80C390-QNR+ 功能描述:8位微控制器 -MCU Dual CAN High-Speed RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
DS80C400 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Network Microcontroller
DS80C400_03 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Network Microcontroller
DS80C400_07 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Network Microcontroller
DS80C400_09 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Network Microcontroller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*