- 您現在的位置：買賣IC網 > PDF目錄10923 > DS80C323-QND/T&R (Maxim Integrated Products)IC MCU HI SPEED 18MHZ IND 44PLCC PDF資料下載
參數資料
| 型號： | DS80C323-QND/T&R |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 15/38頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC MCU HI SPEED 18MHZ IND 44PLCC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 500 |
| 系列： | 80C |
| 核心處理器： | 8051 |
| 芯體尺寸： | 8-位 |
| 速度： | 18MHz |
| 連通性： | EBI/EMI，SIO，UART/USART |
| 外圍設備： | 電源故障復位，WDT |
| 輸入/輸出數： | 32 |
| 程序存儲器類型： | ROMless |
| RAM 容量： | 256 x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 4.5 V ~ 5.5 V |
| 振蕩器型： | 外部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 44-LCC（J 形引線） |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁
DS80C320/DS80C323 High-Speed/Low-Power Microcontrollers
22 of 38
NOTES FOR DS80C320 DC ELECTRICAL CHARACTERISTICS
All parameters apply to both commercial and industrial temperature operation unless otherwise noted. Specifications to -40°C
are guaranteed by design and are not production tested.
1. All voltages are referenced to ground.
2. Active current is measured with a 25MHz clock source driving XTAL1, VCC = RST = 5.5V, all other pins
disconnected.
3. Idle mode current is measured with a 25MHz clock source driving XTAL1, VCC = 5.5V, RST at ground, all
other pins disconnected.
4. Stop mode current measured with XTAL1 and RST grounded, VCC = 5.5V, all other pins disconnected.
5. When addressing external memory. This specification only applies to the first clock cycle following transition.
6. RST = VCC. This condition mimics operation of pins in I/O mode.
7. During a 0-to-1 transition, a one-shot drives the ports hard for two clock cycles. This measurement reflects port
in transition mode.
8. Ports 1 and 3 source transition current when being pulled down externally. It reaches its maximum at
approximately 2V.
9. 0.45<VIN<VCC. Not a high-impedance input. This port is a weak address holding latch because Port 0 is
dedicated as an address bus on the DS80C320. Peak current occurs near the input transition point of the latch,
approximately 2V.
10. Over the industrial temperature range, this specification has a maximum value of 200
A.
11. This is the current required from an external circuit to hold a logic low level on an I/O pin while the
corresponding port latch bit is set to 1. This is only the current required to hold the low level; transitions from 1
to 0 on an I/O pin will also have to overcome the transition current.
12. Device operating range is 4.5V to 5.5V; however, device is tested to 4.0V to ensure proper operation at
minimum VRST.
TYPICAL ICC vs. FREQUENCY
相關PDF資料 |
PDF描述 |
|---|---|
| ISD1740EYI | IC VOICE REC/PLAY 40-SEC 28-TSOP |
| VI-21N-CV-S | CONVERTER MOD DC/DC 18.5V 150W |
| VE-23V-CV-S | CONVERTER MOD DC/DC 5.8V 150W |
| ISD17150EYR | IC VOICE REC/PLAY 150SEC 28-TSOP |
| VE-23T-CV-S | CONVERTER MOD DC/DC 6.5V 150W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS80C323-QNG | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:High-Speed Microcontroller User Guide |
| DS80C323-QNL | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:High-Speed Microcontroller User Guide |
| DS80C323-QNR | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:High-Speed Microcontroller User Guide |
| DS80C323-WCD | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:High-Speed Microcontroller User Guide |
| DS80C323-WCG | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:High-Speed Microcontroller User Guide |
發布緊急采購，3分鐘左右您將得到回復。