- 您現在的位置：買賣IC網 > PDF目錄376978 > DS5000T-8-8 Soft Microcontroller PDF資料下載
參數資料
| 型號： | DS5000T-8-8 |
| 英文描述： | Soft Microcontroller |
| 中文描述： | 軟微控制器 |
| 文件頁數： | 3/19頁 |
| 文件大?。?/td> | 131K |
| 代理商： | DS5000T-8-8 |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁
DS5000(T)
021998 3/19
PIN DESCRIPTION
PIN NUMBER
DESCRIPTION
1–8
P1.0 – P1.7.
General purpose I/O Port 1.
9
RST –
Active high reset input. A logic 1 applied to this pin will activate a reset state. This pin
is pulled down internally so this pin can be left unconnected if not used.
10
P3.0 RXD.
General purpose I/O port pin 3.0. Also serves as the receive signal for the on
board UART. This pin should not be connected directly to a PC COM port.
11
P3.1 TXD.
General purpose I/O port pin 3.1. Also serves as the transmit signal for the on
board UART. This pin should not be connected directly to a PC COM port.
12
P3.2 INT0.
General purpose I/O port pin 3.2. Also serves as the active low External
Interrupt 0.
13
P3.3 INT1.
General purpose I/O port pin 3.3. Also serves as the active low External
Interrupt 1.
14
P3.4 T0.
General purpose I/O port pin 3.4. Also serves as the Timer 0 input.
15
P3.5 T1.
General purpose I/O port pin 3.5. Also serves as the Timer 1 input.
16
P3.6 WR.
General purpose I/O port pin. Also serves as the write strobe for Expanded
bus operation.
17
P3.7 RD.
General purpose I/O port pin. Also serves as the read strobe for Expanded bus
operation.
18, 19
XTAL2, XTAL1.
Used to connect an external crystal to the internal oscillator. XTAL1 is the
input to an inverting amplifier and XTAL2 is the output.
20
GND.
Logic ground.
21–28
P2.0–P2.7.
General purpose I/O Port 2. Also serves as the MSB of the Expanded Address
bus.
29
PSEN –
Program Store Enable. This active low signal is used to enable an external program
memory when using the Expanded bus. It is normally an output and should be unconnected
if not used. PSEN also is used to invoke the Bootstrap Loader. At this time, PSEN will be
pulled down externally. This should only be done once the DS5000(T) is already in a reset
state. The device that pulls down should be open drain since it must not interfere with PSEN
under normal operation.
30
ALE
–
Address Latch Enable. Used to de–multiplex the multiplexed Expanded Address/Data
bus on Port 0. This pin is normally connected to the clock input on a ’373 type transparent
latch. When using a parallel programmer, this pin also assumes the PROG function for pro-
gramming pulses.
31
EA –
External Access. This pin forces the DS5000(T) to behave like an 8031. No internal
memory (or clock) will be available when this pin is at a logic low. Since this pin is pulled down
internally, it should be connected to +5V to use NV RAM. In a parallel programmer, this pin
also serves as V
PP
for super voltage pulses.
相關PDF資料 |
PDF描述 |
|---|---|
| DS5000-32-12 | Soft Microcontroller |
| DS5000-32-16 | Soft Microcontroller Module |
| DS5000-32-8 | Soft Microcontroller |
| DS5000FP | Soft Microprocessor Chip |
| DS5000T | Soft Microcontroller Module |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS5000TK | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller Evaluation Kit |
| DS5001FP | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:128k Soft Microprocessor Chip |
| DS5001FP_05 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:128k Soft Microprocessor Chip |
| DS5001FP08 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| DS5001FP-12 | 功能描述:微處理器 - MPU RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324 |
發布緊急采購，3分鐘左右您將得到回復。