參數資料
型號: DS3994
廠商: Maxim Integrated Products, Inc.
英文描述: 4-Channel Cold-Cathode Fluorescent Lamp Controller
中文描述: 4通道冷陰極熒光燈控制器
文件頁數: 13/28頁
文件大小: 557K
代理商: DS3994
D
4-Channel Cold-Cathode
Fluorescent Lamp Controller
____________________________________________________________________
13
Lamp Strike Frequency Boost
The DS3994 also features a programmable lamp strike
frequency boost option. During the strike period, the
transformer secondary is essentially unloaded. The
lamp frequency be can be easily increased causing a
higher strike voltage. The SB0/1/2 bits in CR3 control
how the frequency is increased during lamp strike. A
setting of 000b results in no frequency increase, while
the maximum setting (111b) causes a 100% increase.
Once the DS3994 detects that the lamp has struck, the
lamp frequency is automatically reset to the nominal
run level.
Lamp Frequency Configuration
The DS3994 can generate its own lamp frequency clock
internally (set LFSS = 0 in CR1), which can then be
sourced to other DS3994s if required, or the lamp clock
can be supplied from an external source (set LFSS = 1 in
CR1). When the lamp clock is internally generated, the
frequency (20kHz to 80kHz) is set by an external resistor
at the LOSC. In this case, the DS3994 can act as a lamp
frequency source because the lamp clock is output at
the LSYNC I/O pin for synchronizing any other DS3994s
configured as lamp frequency receivers.
The DS3994 acts as a lamp frequency receiver when
the lamp clock is supplied externally. In this case, a
20kHz to 80kHz clock must be supplied at the LSYNC
I/O. The external clock can originate from the LSYNC
I/O of a DS3994 configured as a lamp frequency
source or from some other source.
The LOFS bit in CR3 must be set to match the appropri-
ate lamp frequency range. If a 20kHz to 40kHz frequen-
cy is used, then LOFS must be set to 1; if a 40kHz to
80kHz frequency is used, then LOFS must be set to 0.
Configuring Systems with
Multiple DS3994s
The source and receiver options for the lamp frequency
clock and DPWM signal allow multiple DS3994s to be
synchronized in systems requiring more than four
lamps. The lamp and dimming clocks can either be
generated on board the DS3994 using external resis-
tors to set the frequency, or they can be sourced by the
host system to synchronize the DS3994 to other system
resources. Figure 6 shows various multiple DS3994
configurations that allow both lamp and/or DPWM syn-
chronization for all DS3994s in the system.
DPWM Soft-Start
At the beginning of each lamp burst, the DS3994 pro-
vides a soft-start that slowly increases the MOSFET
gate-driver duty cycle (see Figure 7). This minimizes
the possibility of audible transformer noise that could
result from current surges in the transformer primary.
The soft-start length is fixed at 16 lamp cycles.
相關PDF資料
PDF描述
DS4077 77.76MHz VCXO
DS4077L-0C0 77.76MHz VCXO
DS4077L-0CN 77.76MHz VCXO
DS4201 USB Audio DAC(USB音頻數模轉換器)
DS4303 Voltage Sample and Infinite Hold
相關代理商/技術參數
參數描述
DS3994Z+ 功能描述:顯示驅動器和控制器 4-Ch CCFL Controller RoHS:否 制造商:Panasonic Electronic Components 工作電源電壓:2.7 V to 5.5 V 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Reel
DS3994Z+T&R 制造商:Maxim Integrated Products 功能描述:2ND GEN 4CH CCFL CON SOIC-28 T&R LF - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC CCFL CNTRLR 4CH 28-SOIC
DS3994Z+T&R 功能描述:顯示驅動器和控制器 4-Ch CCFL Controller RoHS:否 制造商:Panasonic Electronic Components 工作電源電壓:2.7 V to 5.5 V 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Reel
DS3994Z+W 功能描述:顯示驅動器和控制器 4-Ch CCFL Controller RoHS:否 制造商:Panasonic Electronic Components 工作電源電壓:2.7 V to 5.5 V 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Reel
DS3CC 制造商:Thomas & Betts 功能描述:30A,MG,CUP CAP