參數資料
型號： DS2782
廠商： Maxim Integrated Products, Inc.
英文描述： Stand-Alone Fuel Gauge IC
中文描述： 獨立式電量計IC
文件頁數： 24/25頁
文件大?。?/td> 291K
代理商： DS2782
DS2782: Stand-Alone Fuel Gauge IC
24 of 25
Basic Transaction Formats
Write:
S SAddr W A MAddr A Data0 A P
A write transaction transfers one or more data bytes
to
the DS2782. The data transfer begins at the memory
address supplied in the MAddr byte. Control of the SDA signal is retained by the master throughout the transaction,
except for the Acknowledge cycles.
Read:
S SAddr W A MAddr A Sr SAddr R A Data0 N P
Write Portion
Read Portion
A read transaction transfers one or more bytes
from
the DS2782. Read transactions are composed of two parts, a
write portion followed by a read portion, and is therefore inherently longer than a write transaction. The write portion
communicates the starting point for the read operation. The read portion follows immediately, beginning with a
Repeated START, Slave Address with R/W set to a 1. Control of SDA is assumed by the DS2782 beginning with
the Slave Address Acknowledge cycle. Control of the SDA signal is retained by the DS2782 throughout the
transaction, except for the Acknowledge cycles. The master indicates the end of a read transaction by responding
to the last byte it requires with a No Acknowledge. This signals the DS2782 that control of SDA is to remain with
the master following the Acknowledge clock.
Write Data Protocol
The write data protocol is used to write to register and shadow RAM data to the DS2782 starting at memory
address MAddr. Data0 represents the data written to MAddr, Data1 represents the data written to MAddr + 1 and
DataN represents the last data byte, written to MAddr + N. The master indicates the end of a write transaction by
sending a STOP or Repeated START after receiving the last acknowledge bit.
S SAddr W A MAddr A Data0 A Data1 A … DataN A P
The msb of the data to be stored at address MAddr can be written immediately after the MAddr byte is
acknowledged. Because the address is automatically incremented after the least significant bit (lsb) of each byte is
received by the DS2782, the msb of the data at address MAddr + 1 is can be written immediately after the
acknowledgement of the data at address MAddr. If the bus master continues an auto-incremented write transaction
beyond address 4Fh, the DS2782 ignores the data. Data is also ignored on writes to read-only addresses and
reserved addresses, locked EEPROM blocks as well as a write that auto increments to the Function Command
register (address FEh). Incomplete bytes and bytes that are Not Acknowledged by the DS2782 are not written to
memory. As noted in the Memory Section, writes to unlocked EEPROM blocks modify the shadow RAM only.
Read Data Protocol
The Read Data protocol is used to read register and shadow RAM data from the DS2782 starting at memory
address specified by MAddr. Data0 represents the data byte in memory location MAddr, Data1 represents the data
from MAddr + 1 and DataN represents the last byte read by the master.
S SAddr W A MAddr A Sr SAddr R A Data0 A Data1 A … DataN N P
Data is returned beginning with the most significant bit (msb) of the data in MAddr. Because the address is
automatically incremented after the least significant bit (lsb) of each byte is returned, the msb of the data at
address MAddr + 1 is available to the host immediately after the acknowledgement of the data at address MAddr. If
the bus master continues to read beyond address FFh, the DS2782 outputs data values of FFh. Addresses labeled
“Reserved” in the memory map return undefined data. The bus master terminates the read transaction at any byte
boundary by issuing a No Acknowledge followed by a STOP or Repeated START.
Function Command Protocol
The Function Command protocol executes a device specific operation by writing one of the function command
values (FCmd) to memory address FEh. Table 5 lists the DS2782 FCmd values and describes the actions taken by
each. A one byte write protocol is used to transmit the function command, with the MAddr set to FEh and the data
相關PDF資料
PDF描述
DS3234 Extremely Accurate SPI Bus RTC with Integrated Crystal and SRAM
DS3234S Extremely Accurate SPI Bus RTC with Integrated Crystal and SRAM
DS3234SN Extremely Accurate SPI Bus RTC with Integrated Crystal and SRAM
DS33Z11 Ethernet Mapper
DS33ZH11 Ethernet Mapper
相關代理商/技術參數
參數描述
DS2782_09 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Stand-Alone Fuel Gauge IC
DS2782BE 制造商:Maxim Integrated Products 功能描述:STAND ALONE FG IC 2WIRE 8P TSSOP - Rail/Tube
DS2782BE/T&R 制造商:Maxim Integrated Products 功能描述:STAND ALONG FG IC 2WIRE 8P TSSOP TR - Tape and Reel
DS2782E+ 功能描述:電池管理 Stand-Alone Fuel Gauge RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel
DS2782E+R 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Stand-Alone Fuel Gauge IC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*