- 您現在的位置：買賣IC網 > PDF目錄379183 > DS2770AE Battery Monitor and Charge Controller PDF資料下載
參數資料
| 型號： | DS2770AE |
| 英文描述： | Battery Monitor and Charge Controller |
| 中文描述： | 電池充電控制器監控 |
| 文件頁數： | 19/27頁 |
| 文件大?。?/td> | 272K |
| 代理商： | DS2770AE |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
DS2770
19 of 27
Write Data [6Ch, XX].
This command writes data to the DS2770 starting at memory address XX. The
LSb of the data to be stored at address XX can be written immediately after the MSb of the address has
been entered. Because the address is automatically incremented after the MSb of each byte written, the
LSb to be stored at address XX+1 can be written immediately after the MSb to be stored at address XX. If
the bus master continues to write beyond address FFh, the DS2770 will start over-writing at address 00h.
Writes to read-only addresses, reserved addresses, and locked EEPROM blocks are ignored. Incomplete
bytes are not written. Writes to unlocked EEPROM blocks are to shadow RAM rather than EEPROM.
See the Memory section for more details.
Copy Data [48h, XX].
This command copies the contents of shadow RAM to EEPROM for the
EEPROM block beginning with address XX (20h for block 0, 30h for block 1, and 40h for block 2). Copy
Data commands that address locked blocks are ignored. While the Copy Data command is executing, the
EEC bit in the EEPROM Register is set to 1 and writes to EEPROM addresses are ignored. Reads and
writes to non-EEPROM addresses can still occur while the copy is in progress. The Copy Data command
takes t
EEC
time to execute.
Recall Data [B8h, XX].
This command recalls the contents of the EEPROM block containing the first
address location found in the block to shadow RAM.
Lock [6Ah, XX].
This command locks (write-protects) blocks of EEPROM whose first memory location
is XX (20h for block 0, 30h for block 1, and 40h for block 2). The Lock bit in the EEPROM Register
must be set to 1 before the Lock command is executed. The Lock command must be the next command
issued (after the 1-Wire reset) once the Lock bit has been set. If the Lock bit is 0, the Lock command has
no effect. The Lock command is permanent; a locked block can never be written again. The Lock
command takes t
EEC
time to execute.
Refresh [63h].
The Refresh command restores the Status Register initialization data stored in address
location 31h to the Status Register. The Status Register is initialized directly from the EEPROM and not
from the shadow RAM.
Start Charge [B5h].
The Start Charge command is used to initiate charge through the host interface.
Stop Charge [BEh].
The Stop Charge command is used to terminate charge through the host interface.
相關PDF資料 |
PDF描述 |
|---|---|
| DS2770AE-025 | Battery Monitor and Charge Controller |
| DS2770BE | Battery Monitor and Charge Controller |
| DS28E04-100 | 4096-Bit Addressable 1-Wire EEPROM with PIO |
| DS28E04S-100 | 4096-Bit Addressable 1-Wire EEPROM with PIO |
| DS3151 | Single/Dual/Triple/Quad DS3/E3/STS-1 LIUs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2770AE/R | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Battery Monitor and Charge Controller |
| DS2770AE/T | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Battery Monitor and Charge Controller |
| DS2770AE/T&R | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Battery Monitor and Charge Controller |
| DS2770AE/TR | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| DS2770AE+ | 功能描述:IC BATTERY MONITOR 16-TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT |
發布緊急采購，3分鐘左右您將得到回復。