- 您現在的位置：買賣IC網 > PDF目錄379183 > DS2770AE Battery Monitor and Charge Controller PDF資料下載
參數資料
| 型號： | DS2770AE |
| 英文描述： | Battery Monitor and Charge Controller |
| 中文描述： | 電池充電控制器監控 |
| 文件頁數： | 14/27頁 |
| 文件大?。?/td> | 272K |
| 代理商： | DS2770AE |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
DS2770
14 of 27
STATUS REGISTER FORMAT
Figure 12
Address 01
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
CSTAT1
CSTAT0
PMOD
RNAOP
X
X
CINI
CTYPE
CSTAT1, CSTAT0
— Charge Status. The CSTAT1 and CSTAT0 bits indicate the status of charge per
the table below:
CSTAT1
0
0
1
1
CSTAT0
0
1
0
1
STATUS
No charge source present
Charge in progress
Charge source is present
Charge sequence completed
The charge sequence complete state (1, 1) is present until cleared by a write to the Status Register.
PMOD
— Sleep Mode Enable. A value of 1 in this bit enables the DS2770 to enter Sleep Mode when the
DQ line goes low for greater than two seconds and leaves Sleep Mode when the DQ line goes high. A
value of 0 disables DQ-related transitions into and out of Sleep Mode. The desired default value should
be set in bit 5 of address location 31h. The factory default of the PMOD bit is 0.
RNAOP
— Read Net Address Opcode. A value of 0 in this bit sets the opcode for the Read Net Address
command to 33h, while a 1 sets the opcode to 39h. The desired default value should be set in bit 4 of
address location 31h. The factory default of the RNAOP bit is 0.
CINI
— Charge Initiation Select. The CINI bit is used to determine the method of charge initiation that
will be allowed. A value of 0 indicates that charge may be started only upon use of the Start Charge [B5h]
command. A value of 1 indicates that charge may be started by either the Start Charge command, or by
the application of a charge source at the charge supply input pin, VCH. The desired default value should
be set in bit 1 of address location 31h. The factory default of the CINI bit is 0.
CTYPE
— Charge Type. The charge type bit indicates the Charge Mode that will be used during
charging. A 1 selects NiMH charger operation and a 0 selects rechargeable lithium charger operation. The
desired default value should be set in bit 0 of address location 31h. It is suggested that the EEPROM
block containing the Status Register initiation (location 31h) be locked once the CTYPE and other Status
Register bits are configured to avoid any possible unintended alterations during use. The factory default
of the CTYPE bit is 0.
X
— Reserved Bits.
相關PDF資料 |
PDF描述 |
|---|---|
| DS2770AE-025 | Battery Monitor and Charge Controller |
| DS2770BE | Battery Monitor and Charge Controller |
| DS28E04-100 | 4096-Bit Addressable 1-Wire EEPROM with PIO |
| DS28E04S-100 | 4096-Bit Addressable 1-Wire EEPROM with PIO |
| DS3151 | Single/Dual/Triple/Quad DS3/E3/STS-1 LIUs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2770AE/R | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Battery Monitor and Charge Controller |
| DS2770AE/T | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Battery Monitor and Charge Controller |
| DS2770AE/T&R | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Battery Monitor and Charge Controller |
| DS2770AE/TR | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| DS2770AE+ | 功能描述:IC BATTERY MONITOR 16-TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT |
發布緊急采購，3分鐘左右您將得到回復。