- 您現在的位置：買賣IC網 > PDF目錄1915 > DS26900LN+ (Maxim Integrated Products)IC JTAG MUX/SWITCH 144-LQFP PDF資料下載
參數資料
| 型號： | DS26900LN+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 31/49頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC JTAG MUX/SWITCH 144-LQFP |
| 標準包裝： | 90 |
| 系列： | * |
| 功能： | * |
| 電壓電源： | 單電源 |
| 電壓 - 電源，單路/雙路(±)： | 3.14 V ~ 3.47 V |
| 電流 - 電源： | * |
| 工作溫度： | * |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 144-LQFP |
| 供應商設備封裝： | 144-LQFP（20x20） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁
__________________________________________________________________________________________DS26900
37
8. Additional Application Information
8.1
Accessing Individual Device JTAG on a Board
The DS26900 can be used to provide access to individual device JTAG chains on a board. For this configuration,
TMREQ1 and TMREQ2 are tied high and EREQ is tied low, yielding a single-master configuration with a 5-pin
interface. Individual subports on the DS26900 can be selected in configuration mode.
8.2
Using LED Indicators on the SSPI, ACT and MCI Pins
LED indicators can be attached to the
MCI, ACT, and/or SSPI[4:0] pins by connecting the anode of the LED to V
DD
via a series resistor and the cathode connected to the appropriate DS26900 pin. Series resistance should be no
less than approximately 175
to limit current to 8mA.
8.3
Using 2.7V and 1.8V Logic Levels with the DS26900
The DS26900 operates at a nominal supply voltage of 3.3V. The input buffers are designed to switch at midrail
(VDD/2 = ~1.65V) with some hysteresis. This allows the input buffers the ability to sense 2.7V and 1.8V CMOS logic
levels without modification or configuration in some applications. With that in mind, compatibility with 2.7V and 1.8V
CMOS logic levels (other than 3.3V CMOS logic level) is not expressly guaranteed. The output buffers are capable
of 3.3V CMOS (rail-to-rail) logic levels.
8.4
Series Termination Resistors
Although not part of the IEEE 1149.1 specification, some PCB designs require series termination of clock signals at
the electrical source. For the DS26900, the recommended typical series termination value for outputs is 33
. This
value can vary depending on the PCB’s trace geometries.
相關PDF資料 |
PDF描述 |
|---|---|
| DS275E/T&R | IC TXRX LINE-PWR RS232 14-TSSOP |
| DS276S | IC TXRX LOW POWER RS-232 8-SOIC |
| DS2890P-000+T&R | IC POT DIGITAL 1-WIRE 100K 6TSOC |
| DS28CM00R-A00+T | IC SILICON SERIAL NUMBER SOT23-5 |
| DS30EA101SQE/NOPB | IC CABLE EQUALIZER 16LLP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS26900LN+ | 功能描述:多路器開關 IC JTAG MUX RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
| DS26900N+ | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:JTAG Multiplexer/Switch |
| DS26C31 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:CMOS QUAD TRI-STATE DIFFERENTIAL LINE DRIVER |
| DS26C31 DIE | 制造商:Texas Instruments 功能描述: |
| DS26C31_BBA3026X WAF | 制造商:Texas Instruments 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。