- 您現在的位置：買賣IC網 > PDF目錄1915 > DS2483Q+T (Maxim Integrated Products)IC I2C TO 1WIRE BRIDGE 8TDFN PDF資料下載
參數資料
| 型號： | DS2483Q+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 4/29頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC I2C TO 1WIRE BRIDGE 8TDFN |
| 產品培訓模塊： | Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 系列： | * |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
12
Maxim Integrated
DS2483
Single-Channel 1-Wire Master
with Adjustable Timing and Sleep Mode
Adjust 1-Wire Port
Write Device Configuration
Command Code
C3h
Command Parameter
Control Byte
Description
Updates the selected 1-Wire port parameter, which affects the 1-Wire timing or pullup resis-
tor selection. See Table 6 for the control byte format. Note: Upon a power-on reset or after
a Device Reset command, the parameter default values apply.
Typical Use
To adapt the 1-Wire port to the needs of the application. This can be necessary to accom-
modate the slave timing requirements, which are different at lower pullup voltage.
Restriction
1-Wire activity must have ended before this command can be processed.
Error Response
Command code and data byte are not acknowledged if 1WB = 1 at the time the command
code is received and the command is ignored.
Command Duration
None. The selected port parameter is updated on the rising SCL edge of the control-byte
acknowledge bit.
1-Wire Activity
None
Read Pointer Position
Port Configuration register (for verification).
Status Bits Affected
None
Device Configurations Affected
None
Port Configurations Affected
As specified by the control byte.
Command Code
D2h
Command Parameter
Configuration Byte
Description
Writes a new device configuration byte. The new settings take effect immediately. Note:
When writing to the Device Configuration register, the new data is accepted only if the upper
nibble (bits 7 to 4) is the one’s complement of the lower nibble (bits 3 to 0). When read, the
upper nibble is always 0h.
Typical Use
Defining the features for subsequent 1-Wire communication.
Restriction
1-Wire activity must have ended before the DS2483 can process this command.
Error Response
Command code and parameter are not acknowledged if 1WB = 1 at the time the command
code is received and the command is ignored.
Command Duration
None. The Device Configuration register is updated on the rising SCL edge of the configura-
tion-byte acknowledge bit.
1-Wire Activity
None
Read Pointer Position
Device Configuration register (to verify write).
Status Bits Affected
RST set to 0.
Device Configurations Affected
1WS, SPU, PDN, APU updated.
Port Configurations Affected
None
相關PDF資料 |
PDF描述 |
|---|---|
| DS2490Y | IC BRIDGE CLIP USB TO 1-W 24SOIC |
| DS26303LN-75+A3 | IC LIU E1/T1/J1 3.3V 144-ELQFP |
| DS26324GNA2+ | IC INTERFACE LINE 16CH 256-CSBGA |
| DS26334GN+ | IC INTERFACE LINE 16CH 256-CSBGA |
| DS26401N+ | IC OCTAL FRAMER T1/E1/J1 256-BGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2483R+T | 功能描述:I2C 接口集成電路 Single-Channel 1-Wire Master RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
| DS2483R+U | 功能描述:接口 - 專用 SINGLE-CH 1-WIRE MASTER RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| DS2484Q+T | 制造商:Maxim Integrated Products 功能描述: |
| DS2484R+T | 制造商:Maxim Integrated Products 功能描述: |
| DS2490 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:USB to 1-Wire Bridge Chip |
發布緊急采購，3分鐘左右您將得到回復。