- 您現在的位置：買賣IC網 > PDF目錄11589 > DS2482S-100+ (Maxim Integrated Products)IC BRIDGE I2C TO 1-WIRE 8-SOIC PDF資料下載
參數資料
| 型號： | DS2482S-100+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 19/24頁 |
| 文件大小： | 0K |
| 描述： | IC BRIDGE I2C TO 1-WIRE 8-SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 100 |
| 控制器類型： | I²C 總線控制器 |
| 接口： | I²C |
| 電源電壓： | 3.3V，5V |
| 電流 - 電源： | 750µA |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SOIC |
| 包裝： | 管件 |
| 產品目錄頁面： | 1429 (CN2011-ZH PDF) |
Single-Channel 1-Wire Master
Note 1:
Operating current with 1-Wire write-byte sequence followed by continuously reading the Status Register at 400kHz in overdrive.
Note 2:
With standard speed, the total capacitive load of the 1-Wire bus should not exceed 1nF. Otherwise, the passive pullup on
threshold VIL1 may not be reached in the available time. With overdrive speed, the capacitive load on the 1-Wire bus must
not exceed 300pF.
Note 3:
Active pullup guaranteed to turn on between VIL1(MAX) and VIH1(MIN).
Note 4:
Active or resistive pullup choice is configurable.
Note 5:
Except for tF1, all 1-Wire timing specifications and tAPUOT are derived from the same timing circuit. Therefore, if one of
these parameters is found to be off the typical value, it is safe to assume that all these parameters deviate from their typi-
cal value in the same direction and by the same degree.
Note 6:
These values apply at full load, i.e., 1nF at standard speed and 0.3nF at overdrive speed. For reduced load, the pulldown
slew rate is slightly faster.
Note 7:
Fall time high-to-low (tF1) is derived from PDSRC, referenced from 0.9 x VCC to 0.1 x VCC.
Note 8:
All I2C timing values are referred to VIH(MIN) and VIL(MAX) levels.
Note 9:
Applies to SDA, SCL, AD0 and AD1.
Note 10: The input/output pins of the DS2482-100 do not obstruct the SDA and SCL lines if VCC is switched off.
Note 11: The DS2482-100 provides a hold time of at least 300ns for the SDA signal (referred to the VIH(MIN) of the SCL signal) to
bridge the undefined region of the falling edge of SCL.
Note 12: The maximum tHD:DAT need only be met if the device does not stretch the low period (tLOW) of the SCL signal.
Note 13: A fast-mode I2C bus device can be used in a standard-mode I2C bus system, but the requirement tSU:DAT
≥ 250ns must
then be met. This is automatically the case if the device does not stretch the low period of the SCL signal. If such a device
does stretch the low period of the SCL signal, it must output the next data bit to the SDA line tR(MAX) + tSU:DAT = 1000 +
250 = 1250ns (according to the standard-mode I2C bus specification) before the SCL line is released.
Note 14: CB—Total capacitance of one bus line in pF. If mixed with high-speed-mode devices, faster fall times according to I2C-
Bus Specification Version 2.1 are allowed.
Note 15: I2C communication should not take place for the max tOSCWUP time following a power-on reset.
ELECTRICAL CHARACTERISTICS (continued)
(VCC = 2.9V to 5.5V, TA = -40°C to +85°C.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
Input Capacitance
CI
(Note 9)
10
pF
SCL Clock Frequency
fSCL
0
400
kHz
Hold Time (Repeated) START
Condition (After this period, the
first clock pulse is generated.)
tHD:STA
0.6
μs
Low Period of the SCL Clock
tLOW
1.3
μs
High Period of the SCL Clock
tHIGH
0.6
μs
Setup Time for a Repeated
START Condition
tSU:STA
0.6
μs
Data Hold Time
tHD:DAT
(Notes 11, 12)
0.9
μs
Data Setup Time
tSU:DAT
(Note 13)
250
ns
Setup Time for STOP Condition
tSU:STO
0.6
μs
Bus Free Time Between a STOP
and START Condition
tBUF
1.3
μs
Capacitive Load for Each Bus
Line
CB
(Note 14)
400
pF
Oscillator Warmup Time
tOSCWUP
(Note 15)
100
μs
DS2482-100
4
Maxim Integrated
相關PDF資料 |
PDF描述 |
|---|---|
| PIC16LF1828-E/SO | IC MCU 8BIT 7KB FLASH 20SOIC |
| PIC16F1828-E/SO | IC MCU 8BIT 7KB FLASH 20SOIC |
| PIC16F722T-I/MV | IC MCU 8BIT 3.5KB FLASH 28UQFN |
| VI-BNN-IW-F3 | CONVERTER MOD DC/DC 18.5V 100W |
| PIC16LF722T-I/ML | IC PIC MCU FLASH 3.5KB 28-QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2482S-100/R | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Single-Channel 1-Wire Master |
| DS2482S-100/T | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Single-Channel 1-Wire Master |
| DS2482S-100/T&R | 功能描述:接口 - 專用 RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| DS2482S-100+ | 功能描述:接口 - 專用 1-Wire Master RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| DS2482S-100+T&R | 制造商:Maxim Integrated Products 功能描述: 制造商:Maxim Integrated Products 功能描述:SGL CH 1 WIRE MASTER 8SOIC - Tape and Reel 制造商:Maxim Integrated Products 功能描述:SINGLE-CHANNEL 1-W LN DR 8SO/T&R LF 制造商:Maxim Integrated Products 功能描述:IC I2C TO 1WIRE BRIDGE 8SOIC 制造商:Maxim Integrated Products 功能描述:I2C to 1 Wire Bridge Device SOIC8 T/R |
發布緊急采購，3分鐘左右您將得到回復。