- 您現在的位置：買賣IC網 > PDF目錄10656 > DS2480B+T&R (Maxim Integrated Products)IC LINE DRVR W/SENSOR 1-W 8SOIC PDF資料下載
參數資料
| 型號： | DS2480B+T&R |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 4/32頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC LINE DRVR W/SENSOR 1-W 8SOIC |
| 產品培訓模塊： | 1-Wire Communications Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1 |
| 系列： | * |
| 其它名稱： | DS2480B+T&RDKR |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
DS2480B
Maxim Integrated........................................................................................................................................................................................... 12
Table 3. CONFIGURATION PARAMETER OVERVIEW
Parameter
Description
Configurable at
Default
Par. Code
Standard Flexible Overdrive Reg./Flex. Overdrive
Pulldown Slew Rate
Control
001
√
15V/s
Programming Pulse
Duration
010
√
512s
Strong Pullup Duration
011
√
524ms
Write-1 Low Time
100
√
8s
1s
Data Sample Offset and
Write 0 Recovery Time
101
√
3s
1s
3s
RS232 Baud Rate
111
√
9.6kbps
The numbers given for parameter 001 (Pulldown Slew Rate Control) are nominal values. They may vary
to some extent and are almost independent of the load on the 1-Wire bus. Information on how to select
the optimum value of this parameter is given in the Controlled Edges section .
For the parameters 010 (Programming Pulse Duration) and 011 (Strong Pullup Duration) one may select
indefinite duration. This value, however, should only be selected if one is not going to switch the device
to Data Mode. As long as the device stays in Command Mode, any pulse function (programming or
strong pullup) that uses one of these parameters can be terminated by sending the command code F1h.
Termination is not possible if the device is in Data Mode.
Parameter 111 (RS232 Baud Rate) has two functions. It selects the baud rate and allows inversion of the
signal at the RXD pin. Using one of the value codes 100 to 111 will set the polarity at RXD to the
opposite of what is defined by the logic level at the POL pin (asymmetry bit, see Figure 1). This may
reduce the component count in some applications of the device. Note that when changing the baud rate,
the DS2480B will send the command response byte at the new data rate.
A short explanation on the use of parameters 100 (Write-1 Low Time) and 101 (Data Sample
Offset/Write-0 Recovery Time) is given in the Timing Diagrams section later in this document.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX967ESA+T | IC COMPARATOR R-R 8-SOIC |
| AD774BKNZ | IC ADC 12BIT W/BUFF REF 28DIP |
| MAX967EUA+T | IC COMPARATOR R-R 8-UMAX |
| LTC1608ACG#PBF | IC A/D CONV 16BIT SAMPLNG 36SSOP |
| MAX932CUA+T | IC COMPARATOR W/REF 8-UMAX |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2480S | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Serial 1.Wire Line Driver |
| DS2482-100 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Single-Channel 1-Wire Master |
| DS2482-100_12 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Single-Channel 1-Wire Master |
| DS2482-101 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Single-Channel 1-Wire Master with Sleep Mode |
| DS2482-101_12 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Single-Channel 1-Wire Master with Sleep Mode |
發布緊急采購，3分鐘左右您將得到回復。