- 您現在的位置：買賣IC網 > PDF目錄385273 > DS2422 (MAXIM INTEGRATED PRODUCTS INC) 1K-Bit 1-Wire RAM with Counters(帶計數器的1K位1線串行RAM) PDF資料下載
參數資料
| 型號： | DS2422 |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | DRAM |
| 英文描述： | 1K-Bit 1-Wire RAM with Counters(帶計數器的1K位1線串行RAM) |
| 中文描述： | 1K X 1 STANDARD SRAM, PDSO6 |
| 封裝： | 3.70 X 4 X 1.50 MM, TSOC-6 |
| 文件頁數： | 17/23頁 |
| 文件大小： | 146K |
| 代理商： | DS2422 |
DS2422/DS2423
021998 17/23
1–WIRE SIGNALING
The DS242X requires strict protocols to insure data
integrity. The protocol consists of four types of signaling
on one line: Reset Sequence with Reset Pulse and
Presence Pulse, Write 0, Write 1 and Read Data. All
these signals except presence pulse are initiated by the
bus master. The DS242X can communicate at two dif-
ferent speeds, regular speed and Overdrive Speed. If
not explicitly set into the Overdrive mode, the DS242X
will communicate at regular speed. While in Overdrive
Mode the fast timing applies to all wave forms.
The initialization sequence required to begin any com-
munication with the DS242X is shown in
Figure 10. A
reset pulse followed by a presence pulse indicates the
DS242X is ready to send or receive data given the cor-
rect ROM command and memory function command.
The bus master transmits (TX) a reset pulse (t
RSTL
,
minimum 480
μ
s at regular speed, 48
μ
s at Overdrive
Speed). The bus master then releases the line and
goes into receive mode (RX). The 1–Wire bus is pulled
to a high state via the pull–up resistor. After detecting
the rising edge on the data pin, the DS242X waits (t
PDH
,
15–60
μ
s at regular speed, 2–6
μ
s at Overdrive speed)
and then transmits the presence pulse (t
PDL
, 60–240
μ
s
at regular speed, 8–24
μ
s at Overdrive Speed).
A Reset Pulse of 480
μ
s or longer will exit the Overdrive
Mode returning the device to regular speed. If the
DS242X is in Overdrive Mode and the Reset Pulse is no
longer than 80
μ
s the device will remain in Overdrive
Mode.
Read/Write Time Slots
The definitions of write and read time slots are illustrated
in Figure 11. All time slots are initiated by the master
driving the data line low. The falling edge of the data line
synchronizes the DS242X to the master by triggering a
delay circuit in the DS242X. During write time slots, the
delay circuit determines when the DS242X will sample
the data line. For a read data time slot, if a “0” is to be
transmitted, the delay circuit determines how long the
DS242X will hold the data line low overriding the 1 gen-
erated by the master. If the data bit is a “1”, the device
will leave the read data time slot unchanged.
INITIALIZATION PROCEDURE “RESET AND PRESENCE PULSES”
Figure 10
t
RSTH
t
RSTL
t
R
V
PULLUP
V
PULLUP MIN
IH MIN
V
IL MAX
Regular Speed
480
μ
s < t
RSTL
<
480
μ
s < t
RSTH
<
15
μ
s < t
PDH
< 60
μ
s
60
μ
s < t
PDL
< 240
μ
s
*
**
t
PDH
t
PDL
MASTER R
X
“PRESENCE PULSE”
MASTER T
X
“RESET PULSE”
RESISTOR
MASTER
DS242X
Overdrive Speed
48
μ
s < t
RSTL
< 80
μ
s
48
μ
s < t
RSTH
<
2
μ
s < t
PDH
< 6
μ
s
8
μ
s < t
PDL
< 24
μ
s
**
*IN ORDER NOT TO MASK INTERRUPT SIGNALING BY OTHER DEVICES ON THE 1–WIRE BUS, t
RSTL
+t
R
SHOULD ALWAYS BE LESS THAN 960
μ
s
**INCLUDES RECOVERY TIME
相關PDF資料 |
PDF描述 |
|---|---|
| DS2423 | 4K-Bit 1-Wire RAM with Counters(帶計數器的4K位1線串行RAM) |
| DS2450 | 1-Wire Quad A/D Converter(1線串行四路A/D轉換器) |
| DS2480 | Serial 1-Wire Line Driver(1線串行線驅動器) |
| DS2505-UNW | UniqueWare Add-only Memory(專用只加存儲器) |
| DS2506-UNW | UniqueWare Add-only Memory(專用只加存儲器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2422P | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Serial SRAM |
| DS2422S | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS2422S+ | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS2422X | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS2423 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:4kbit 1-Wire RAM with Counter |
發布緊急采購，3分鐘左右您將得到回復。