參數資料
型號： DS2422
英文描述： 1-Wire Temperature/Datalogger with 8kB Datalog Memory
中文描述： 1-Wire®溫度/數據記錄器，帶有8KB數據記錄存儲器
文件頁數： 27/48頁
文件大?。?/td> 444K
代理商： DS2422
DS2422
27 of 48
COPY SCRATCHPAD WITH PASSWORD [99h]
This command is used to copy data from the scratchpad to the writable memory sections. After issuing the Copy
Scratchpad command, the master must provide a 3-byte authorization pattern, which can be obtained by reading
the scratchpad for verification. This pattern must exactly match the data contained in the three address registers
(TA1, TA2, E/S, in that order). Next the master must transmit the 64-bit full-access password. If passwords are
enabled and the transmitted password is different from the stored full-access password, the Copy Scratchpad with
Password command will fail. The device will stop communicating and will wait for a reset pulse. If the password
was correct or if passwords were not enabled, the device will test the 3-byte authorization code. If the authorization
code pattern matches, the AA (Authorization Accepted) flag will be set and the copy will begin. A pattern of
alternating 1s and 0s will be transmitted after the data has been copied until the master issues a reset pulse. While
the copy is in progress any attempt to reset the part will be ignored. Copy typically takes 2μs per byte.
The data to be copied is determined by the three address registers. The scratchpad data from the beginning offset
through the ending offset will be copied, starting at the target address. Anywhere from 1 to 32 bytes may be copied
to memory with this command. The AA flag will remain at logic 1 until it is cleared by the next Write Scratchpad
command. With suitable password, the copy scratchpad will always function for the 16 pages of data memory and
the 2 pages of calibration memory. While a mission is in progress, write attempts to the register pages will not be
successful. The AA bit (Authorization Accepted) remaining at 0 will indicate this.
READ MEMORY WITH PASSWORD AND CRC [69h]
The Read Memory with CRC command is the general function to read from the device. This command generates
and transmits a 16-bit CRC following the last data byte of a memory page.
After having sent the command code of the Read Memory with CRC command, the bus master sends a 2-byte
address that indicates a starting byte location. Next the master must transmit one of the 64-bit passwords. If
passwords are enabled and the transmitted password does not match one of the stored passwords, the Read
Memory with Password and CRC command will fail. The device will stop communicating and will wait for a reset
pulse. If the password was correct or if passwords were not enabled, the master reads data from the DS2422
beginning from the starting address and continuing until the end of a 32-byte page is reached. At that point the bus
master will send 16 additional read data time slots and receive the inverted 16-bit CRC. With subsequent read data
time slots the master will receive data starting at the beginning of the next memory page followed again by the
CRC for that page. This sequence will continue until the bus master resets the device. When trying to read the
passwords or memory areas that are marked as "reserved", the DS2422 will transmit 00h or FFh bytes
respectively. The CRC at the end of a 32-byte memory page is based on the data as it was transmitted.
With the initial pass through the Read Memory with CRC flow, the 16-bit CRC value is the result of shifting the
command byte into the cleared CRC generator followed by the 2 address bytes and the contents of the data
memory. Subsequent passes through the Read Memory with CRC flow will generate a 16-bit CRC that is the result
of clearing the CRC generator and then shifting in the contents of the data memory page. After the 16-bit CRC of
the last page is read, the bus master will receive logical 1s from the DS2422 until a reset pulse is issued. The Read
Memory with CRC command sequence can be ended at any point by issuing a reset pulse.
相關PDF資料
PDF描述
DS2422S 1-Wire Temperature/Datalogger with 8kB Datalog Memory
DS2482-800 Eight-Channel 1-Wire Master
DS2482-100 Single-Channel 1-Wire Master
DS2482S-100 Single-Channel 1-Wire Master
DS2482S-800 Eight-Channel 1-Wire Master
相關代理商/技術參數
參數描述
DS2422P 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Serial SRAM
DS2422S 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
DS2422S+ 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
DS2422X 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
DS2423 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:4kbit 1-Wire RAM with Counter
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*