參數資料
型號： DS2422
英文描述： 1-Wire Temperature/Datalogger with 8kB Datalog Memory
中文描述： 1-Wire®溫度/數據記錄器，帶有8KB數據記錄存儲器
文件頁數： 19/48頁
文件大?。?/td> 444K
代理商： DS2422
DS2422
19 of 48
Register Details
BIT DESCRIPTION
BIT(S)
DEFINITION
MIP: Mission In Progress
b1
If this bit reads 1 the device has been set up for a mission and this
mission is still in progress. The MIP bit returns from logic 1 to logic 0
when a mission is ended. See function commands Start Mission and
Stop Mission.
If this bit reads 1, the Mission Time Stamp, Mission Samples Counter,
as well as all the alarm flags of the Alarm Status Register have been
cleared in preparation of a new mission. Executing the Clear Memory
command clears these memory sections. The MEMCLR bit will return
to 0 as soon as a new mission is started by using the Start Mission
command. The memory has to be cleared in order for a mission to
start.
If this bit reads 1, the Mission Start upon Temperature Alarm was
selected and the Start Mission command was successfully executed,
but the device has not yet experienced the temperature alarm. This bit
is cleared after a temperature alarm event, but is not affected by the
Clear Memory command. Once set, WFTA remains set if a mission is
stopped before a temperature alarm occurs. To clear WFTA manually
before starting a new mission, set the high temperature alarm (address
0209h) to -40°C and perform a forced conversion.
MEMCLR: Memory
Cleared
b3
WFTA: Waiting for
Temperature Alarm
b4
MISSION START DELAY
The content of the Mission Start Delay Counter tells how many minutes will have to expire from the time
a mission
was started until the first measurement of the mission will take place (SUTA = 0) or until the device will start testing
the temperature for a temperature alarm (SUTA = 1). The Mission Start Delay is stored as an unsigned 24-bit
integer number. The maximum delay is 16777215 minutes, equivalent to 11650 days or roughly 31 years. If the
start delay is non-zero and the SUTA bit is set to 1, first the delay has to expire before the device starts testing for
temperature alarms to begin logging data.
Mission Start Delay Counter
ADDR
0216h
0217h
0218h
b7
b6
b5
b4
b3
b2
b1
b0
Delay Low Byte
Delay Center Byte
Delay High Byte
During a mission, there is only read access to these registers.
For a typical mission, the Mission Start Delay is 0. If a mission is too long for a single DS2422 to store all readings
at the selected sample rate, one can use several devices and set the Mission Start Delay for the second device to
start recording as soon as the memory of the first device is full, and so on. The RO-bit in the Mission Control
Register (address 0213h) must be set to 0 to prevent overwriting of collected data once the datalog memory is full.
MISSION TIME STAMP
The Mission Time Stamp indicates the date and time of the first logged temperature and/or data sample of the
mission. There is only read access to the Mission Time Stamp Register.
Mission Time Stamp Registers Bitmap
ADDR
0219h
021Ah
021Bh
b7
0
0
0
b6
b5
b4
b3
b2
b1
b0
10 Seconds
10 Minutes
20h.
AM/PM
Single Seconds
Single Minutes
Single Hours
12/24
10h.
021Ch
021Dh
021Eh
0
0
0
10 Date
Single Date
Single Months
Single Years
CENT
0
10m.
10 Years
相關PDF資料
PDF描述
DS2422S 1-Wire Temperature/Datalogger with 8kB Datalog Memory
DS2482-800 Eight-Channel 1-Wire Master
DS2482-100 Single-Channel 1-Wire Master
DS2482S-100 Single-Channel 1-Wire Master
DS2482S-800 Eight-Channel 1-Wire Master
相關代理商/技術參數
參數描述
DS2422P 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Serial SRAM
DS2422S 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
DS2422S+ 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
DS2422X 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
DS2423 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:4kbit 1-Wire RAM with Counter
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*