參數資料
型號： DS2408S+
廠商： Maxim Integrated Products
文件頁數： 17/39頁
文件大小： 0K
描述： IC SWITCH 8-CHAN ADDRESS 16SOIC
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 50
接口： 1 線
輸入/輸出數： 8
中斷輸出： 無
電源電壓： 2.8 V ~ 5.25 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 16-SOIC（0.154"，3.90mm 寬）
供應商設備封裝： 16-SOIC
包裝： 管件
DS2408
24 of 39
1-WIRE SIGNALING
The DS2408 requires strict protocols to ensure data integrity. The protocol consists of four types of
signaling on one line: Reset Sequence with Reset Pulse and Presence Pulse, Write-Zero, Write-One, and
Read-Data. Except for the presence pulse, the bus master initiates all these signals. The DS2408 can
communicate at two different speeds, standard speed, and overdrive speed. If not explicitly set into the
overdrive mode, the DS2408 will communicate at standard speed. While in overdrive mode, the fast
timing applies to all waveforms.
To get from idle to active, the voltage on the 1-Wire line needs to fall from VPUP below the VTL threshold.
To get from active to idle, the voltage needs to rise from VILMAX past the VTH threshold. The VILMAX
voltage is relevant for the DS2408 when determining a logical level, not triggering any events.
Figure 13 shows the initialization sequence required to begin any communication with the DS2408. A
Reset Pulse followed by a Presence Pulse indicates the DS2408 is ready to receive data, given the correct
ROM and control function command. If the bus master uses slew-rate control on the falling edge, it must
pull down the line for tRSTL + tF to compensate for the edge. A tRSTL duration of 480s or longer will exit
the overdrive mode returning the device to standard speed. If the DS2408 is in overdrive mode and tRSTL
is no longer than 80s the device will remain in overdrive mode.
Figure 13. INITIALIZATION PROCEDURE “RESET AND PRESENCE PULSES”
After the bus master has released the line it goes into receive mode (RX). The 1-Wire bus is then pulled
to VPUP via the pullup resistor or, in case of a DS2480B driver, by active circuitry. When the VTH
threshold is crossed, the DS2408 waits for tPDH and then transmits a Presence Pulse by pulling the line
low for tPDL. To detect a presence pulse, the master must test the logical state of the 1-Wire line at tMSP.
The tRSTH window must be at least the sum of tPDHMAX, tPDLMAX, and tRECMIN. Immediately after tRSTH is
expired, the DS2408 is ready for data communication. In a mixed population network, tRSTH should be
extended to a minimum of 480s at standard speed and 48s at overdrive speed to accommodate other 1-
Wire devices.
相關PDF資料
PDF描述
MAX7300AAI+ IC I/O EXPANDER I2C 28B 28SSOP
MAX7311AUG+ IC I/O EXPANDER I2C 16B 24TSSOP
MAX7311ATG+ IC I/O EXPANDER I2C 16B 24TQFN
MAX7311AWG+ IC I/O EXPANDER I2C 16B 24SOIC
MAX7314ATG+ IC I/O EXPANDER I2C 16B 24TQFN
相關代理商/技術參數
參數描述
DS2408S/R 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:1-Wire 8-Channel Addressable Switch
DS2408S/T 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:1-Wire 8-Channel Addressable Switch
DS2408S/T&R 功能描述:接口 - 專用 RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
DS2408S+ 功能描述:接口 - 專用 1-Wire 8-Ch Addressable Switch RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
DS2408S+T&R 制造商:Maxim Integrated Products 功能描述:ADDRESSABLE SWIT 16SOIC N - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC SWITCH 8-CHAN ADDRESS 16SOIC 制造商:Maxim Integrated Products 功能描述:Interface - Specialized 1-Wire 8-Ch Addressable Switch
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*