- 您現在的位置：買賣IC網 > PDF目錄376968 > DS2404-001 EconoRAM Time Chip PDF資料下載
參數資料
| 型號： | DS2404-001 |
| 英文描述： | EconoRAM Time Chip |
| 中文描述： | EconoRAM時鐘芯片 |
| 文件頁數： | 17/28頁 |
| 文件大?。?/td> | 663K |
| 代理商： | DS2404-001 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
DS2404
17 of 28
020998
1-WIRE SIGNALING
The DS2404 requires strict protocols to ensure data integrity. The protocol consists of five types of
signaling on one line: Reset Sequence with reset pulse and presence pulse, write 0, write 1, Read Data
and interrupt pulse. All these signals except presence pulse and interrupt pulse are initiated by the bus
master.
The initialization sequence required to begin any communication with the DS2404 is shown in Figure 10.
A reset pulse followed by a presence pulse indicates the DS2404 is ready to send or receive data given the
correct ROM command and memory function command.
The bus master transmits (T
X
) a reset pulse (t
RSTL
, minimum of 480
μ
s). The bus master then releases the
line and goes into receive mode (R
X
). The 1-Wire bus is pulled to a high state via the pull-up resistor.
After detecting the rising edge on the date line, the DS2404 waits (t
PDH
, 15-60
μ
s) and then transmits the
presence pulse (t
PDL
, 60 - 240
μ
s). There are special conditions if interrupts are enabled where the bus
master must check the state of the 1-Wire bus after being in the R
X
mode for 480
μ
s. These conditions
will be discussed in the “Interrupt” section.
READ/WRITE TIME SLOTS
The definitions of write and read time slots are illustrated in Figure 11. All time slots are initiated by the
master driving the data line low. The falling edge of the data line synchronizes the DS2404 to the master
by triggering a delay circuit in the DS2404. During write time slots, the delay circuit determines when the
DS2404 will sample the data line. For a read data time slot, if a “0” is to be transmitted, the delay circuit
determines how long the DS2404 will hold the data line low overriding the 1 generated by the master. If
the data bit is a “1”, the device will leave the read data time slot unchanged.
INITIALIZATION PROCEDURE “RESET AND PRESENCE PULSES”
Figure 10
480
μ
s
≤
t
RSTL
<
∞
*
480
μ
s
≤
t
RSTH
<
∞
(includes recovery time)
15
μ
s
≤
t
PDH
< 60
μ
s
60
μ
s
≤
t
PDL
< 240
μ
s
In order not to mask interrupt signaling by other devices on the 1-Wire bus, t
RSTL
+ t
R
should always
be less than 960
μ
s.
RESISTOR
MASTER
DS2404
相關PDF資料 |
PDF描述 |
|---|---|
| DS2404B | EconoRAM Time Chip |
| DS2404S | EconoRAM Time Chip |
| DS2405 | Addressable Switch |
| DS2405P | Addressable Switch |
| DS2405T | Addressable Switch |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2404-001+ | 制造商:Maxim Integrated Products 功能描述:REAL TIME CLOCK SERL 512BYTE 16PDIP - Rail/Tube |
| DS2404B | 功能描述:實時時鐘 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| DS2404B/T&R | 制造商:Maxim Integrated Products 功能描述:ECONORAM/TIME, SSOP16-TRL (GENERIC) - Tape and Reel |
| DS2404B+ | 制造商:Maxim Integrated Products 功能描述:REAL TIME CLOCK SERL 512BYTE 16SSOP - Rail/Tube |
| DS2404B+T&R | 制造商:Maxim Integrated Products 功能描述:REAL TIME CLOCK SERL 512BYTE 16SSOP - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。