- 您現在的位置：買賣IC網 > PDF目錄1914 > DS2148T (Maxim Integrated Products)IC LIU E1/T1/J1 5V 44-TQFP PDF資料下載
參數資料
| 型號： | DS2148T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 4/73頁 |
| 文件大小： | 0K |
| 描述： | IC LIU E1/T1/J1 5V 44-TQFP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS |
| 產品變化通告： | Product Discontinuation 20/Feb/2012 |
| 標準包裝： | 160 |
| 類型： | 線路接口裝置（LIU） |
| 驅動器/接收器數： | 1/1 |
| 規程： | T1/E1/J1 |
| 電源電壓： | 4.75 V ~ 5.25 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 44-TQFP |
| 供應商設備封裝： | 44-TQFP（10x10） |
| 包裝： | 管件 |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁
DS2148/DS21Q48
12 of 73
Table 2-3. Pin Descriptions in Parallel Port Mode (Sorted by Pin Name,
DS2148T)
NAME
PIN
I/O
FUNCTION
A0
to
A4
11
to
7
I
Address Bus. In nonmultiplexed bus operation (BIS1 = 0, BIS0 = 1),
serves as the address bus. In multiplexed bus operation (BIS1 = 0, BIS0 =
0), these pins are not used and should be tied low.
ALE(AS)
4
I
Address Latch Enable (Address Strobe). When using the parallel port
(BIS1 = 0) in multiplexed bus mode (BIS0 = 0), serves to demultiplex the
bus on a positive-going edge. In nonmultiplexed bus mode (BIS0 = 1),
should be tied low.
BIS0/BIS1
32/33
I
Bus Interface Select Bits 0 & 1. Used to select bus interface option. See
Table 2-1 for details.
BPCLK
31
O
Backplane Clock. A 16.384MHz, 8.192MHz, 4.096MHz, or 2.048MHz
clock output that is referenced to RCLK selectable via CCR5.7 and
CCR5.6. In hardware mode, defaults to 16.384MHz output.
CS
1
I
Active-Low Chip Select. Must be low to read or write to the device.
D0/AD0
to
D7/AD7
19
to
12
I/O
Data Bus/Address/Data Bus. In non-multiplexed bus operation (BIS1 =
0, BIS0 = 1), serves as the data bus. In multiplexed bus operation (BIS1 =
0, BIS0 = 0), serves as an 8-bit multiplexed address/data bus.
HRST
29
I
Active-Low Hardware Reset. Bringing
HRST low will reset the DS2148
setting all control bits to their default state of all zeros.
INT
23
O
Active-Low Interrupt. Flags host controller during conditions and
change of conditions defined in the Status Register. Active low, open
drain output.
MCLK
30
I
Master Clock. A 2.048MHz (±50ppm) clock source with TTL levels is
applied at this pin. This clock is used internally for both clock/data
recovery and for jitter attenuation. Use of a T1 1.544MHz clock source is
optional.
See Note 1 on clock accuracy at the end of this table.
NA
-
I
Not Assigned. Should be tied low.
PBEO
24
O
PRBS Bit Error Output. The receiver will constantly search for a 215-1 or
a 220-1 PRBS depending on the ETS bit setting (CCR1.7). Remains high if
out of synchronization with the PRBS pattern. Goes low when
synchronized to the PRBS pattern. Any errors in the received pattern after
synchronization will cause a positive going pulse (with same period as E1
or T1 clock) synchronous with RCLK. PRBS bit errors can also be
reported to the ECR1 and ECR2 registers by setting CCR6.2 to a logic 1.
PBTS
44
I
Parallel Bus Type Select. When using the parallel port (BIS1 = 0), set
high to select Motorola bus timing, set low to select Intel bus timing. This
pin controls the function of the
RD(DS), ALE(AS), and WR(R/W) pins. If
PBTS = 1 and BIS1 = 0, then these pins assume the Motorola function
listed in parenthesis (). In serial port mode, this pin should be tied low.
RCLK
40
O
Receive Clock. Buffered recovered clock from the line. Synchronous to
MCLK in absence of signal at RTIP and RRING.
RD(DS)
2
I
Active-Low Read Input (Data Strobe). DS is active low when in
nonmultiplexed, Motorola mode. See the bus timing diagrams in Section
RCL/LOTC
25
O
Receive Carrier Loss/Loss of Transmit Clock. An output which will
toggle high during a receive carrier loss (CCR2.7 = 0) or will toggle high
if the TCLK pin has not been toggled for 5
s ±2s (CCR2.7 = 1). CCR2.7
defaults to logic 0 when in hardware mode.
相關PDF資料 |
PDF描述 |
|---|---|
| DS2149Q+ | IC LIU T1/J1 5V 28-PLCC |
| DS2151QN | IC TXRX T1 1-CH 5V LP IND 44PLCC |
| DS2152L+ | IC TXRX T1 1CHIP ENHNCD 100-LQFP |
| DS2153Q-A7+T&R | IC TXRX E1 1-CHIP 5V 44-PLCC |
| DS2154LNA2+ | IC TXRX E1 5V 100-LQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2148T+ | 功能描述:網絡控制器與處理器 IC 5V E1/T1/J1 Line Interface RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS2148TA2 | 功能描述:網絡控制器與處理器 IC 5V E1/T1/J1 Line Interface RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS2148TB | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS2148TC1 | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS2148TN | 功能描述:網絡控制器與處理器 IC 5V E1/T1/J1 Line Interface RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。