- 您現在的位置：買賣IC網 > PDF目錄358701 > DS1922T Temperature Logger iButton with 8kB Datalog Memory PDF資料下載
參數資料
| 型號： | DS1922T |
| 英文描述： | Temperature Logger iButton with 8kB Datalog Memory |
| 文件頁數： | 24/48頁 |
| 文件大?。?/td> | 428K |
| 代理商： | DS1922T |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
DS1922L/DS1922T
24 of 48
MISSIONING
The typical task of the DS1922L/T iButton is recording temperature. Before the device can perform this function, it
needs to be set up properly. This procedure is called missioning.
First of all, DS1922L/T needs to have its real-time clock set to valid time and date. This reference time may be the
local time, or, when used inside of a mobile unit, UTC (also called GMT, Greenwich Mean Time) or any other time
standard that was agreed upon. The real-time clock oscillator must be running (EOSC = 1). The memory assigned
to store the Mission Time Stamp, Mission Samples Counter, and Alarm Flags must be cleared using the Memory
Clear command. To enable the device for a mission, the ETL-bit must be set to 1. These are general settings that
have to be made in any case, regardless of the type of object to be monitored and the duration of the mission.
If alarm signaling is desired, the temperature alarm low and high thresholds must be defined. How to convert a
temperature value into the binary code to be written to the threshold registers is described under
Temperature
Conversion
earlier in this document. In addition, the temperature alarm must be enabled for the low- and/or high-
threshold. This makes the device respond to a Conditional Search command (see
ROM Function Commands
),
provided that an alarming condition has been encountered.
The setting of the RO bit (rollover enable) and sample rate depends on the duration of the mission and the
monitoring requirements. If the most recently logged data is important, the rollover should be enabled (RO = 1).
Otherwise one should estimate the duration of the mission in minutes and divide the number by 8192 (8-bit format)
or 4096 (16-bit format) to calculate the value of the sample rate (number of minutes between conversions). If the
estimated duration of a mission is 10 days (= 14400 minutes), for example, then the 8192-byte capacity of the
datalog memory would be sufficient to store a new 8-bit value every 1.8 minutes (110 seconds). If the datalog
memory of the DS1922L/T is not large enough to store all readings, one can use several devices and set the
Mission Start Delay to values that make the second device start logging as soon as the memory of the first device
is full, and so on. The RO bit needs to be set to 0 to disable rollover that would otherwise overwrite the logged data.
After the RO bit and the Mission Start Delay are set, the sample rate needs to be written to the Sample Rate
Register. The sample rate may be any value from 1 to 16383, coded as an unsigned 14-bit binary number.
A
sample rate of all zeros is not valid and must be avoided under all circumstances. This will cause the
device to enter into an unrecoverable state.
The fastest sample rate is one sample per second (EHSS = 1,
Sample Rate = 0001h) and the slowest is one sample every 273.05 hours (EHSS = 0, Sample Rate = 3FFFh). To
get one sample every 6 minutes, for example, the sample rate value needs to be set to 6 (EHSS = 0) or 360
decimal (equivalent to 0168h at EHSS = 1).
If there is a risk of unauthorized access to the DS1922L/T or manipulation of data, one should define passwords for
read access and full access. Before the passwords become effective, their use needs to be enabled. See Security
by Password for more details.
The last step to begin a mission is to issue the Start Mission command. As soon as it has received this command,
the DS1922L/T sets the MIP flag and clear the MEMCLR flag. With the immediate/delayed start mode (SUTA = 0),
after as many minutes as specified by the Mission Start Delay are over, the device will wake up, copy the current
date and time to the mission time stamp register, and log the first entry of the mission. This increments both the
Mission Samples Counter and Device Samples Counter. All subsequent log entries will be made as specified by
the value in the Sample Rate Register and the EHSS bit.
If the Start Upon Temperature Alarm mode is chosen (SUTA = 1) and temperature logging is enabled (ETL = 1) the
DS1922L/T first waits until the start delay is over. Then the device wakes up in intervals as specified by the sample
rate and EHSS bit and measure the temperature. This will increment the Device Samples Counter only. Only after
an alarming temperature is encountered will the DS1922L/T set the mission time stamp. The first sample of the
mission is logged one sample period after the temperature alarm occurred. From then on, both the Mission
Samples Counter and Device Samples Counter increment at the same time. All subsequent log entries are made
as specified by the value in the Sample Rate Register and the EHSS bit.
The general-purpose memory operates independently of the other memory sections and is not write-protected
during a mission. All memory of the DS1922L/T can be read at any time, e. g., to watch the progress of a mission.
Attempts to read the passwords will read 00h bytes instead of the data that is stored in the password registers.
相關PDF資料 |
PDF描述 |
|---|---|
| DS1922L-F5 | Temperature Logger iButton With 8kB Datalog Memory |
| DS1992 | 1kb/4kb Memory iButton |
| DS1993 | 1kb/4kb Memory iButton |
| DS1992L-F5 | 1kbit/4kbit Memory iButtonTM DS1994 4-kbit Plus Time Memory iButtonTM |
| DS21349DK | T1/J1 Line Interface Unit Design Kit |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1922T-A1F | 功能描述:iButton RoHS:否 存儲類型:SRAM 存儲容量:512 B 組織: 工作電源電壓:3 V to 5.25 V 接口類型:1-Wire 最大工作溫度:+ 85 C 尺寸:17.35 mm x 5.89 mm 封裝 / 箱體:F5 MicroCan 制造商:Maxim Integrated |
| DS1922T-A1F+ | 功能描述:iButton RoHS:否 存儲類型:SRAM 存儲容量:512 B 組織: 工作電源電壓:3 V to 5.25 V 接口類型:1-Wire 最大工作溫度:+ 85 C 尺寸:17.35 mm x 5.89 mm 封裝 / 箱體:F5 MicroCan 制造商:Maxim Integrated |
| DS1922T-F5 | 功能描述:iButton RoHS:否 存儲類型:SRAM 存儲容量:512 B 組織: 工作電源電壓:3 V to 5.25 V 接口類型:1-Wire 最大工作溫度:+ 85 C 尺寸:17.35 mm x 5.89 mm 封裝 / 箱體:F5 MicroCan 制造商:Maxim Integrated |
| DS1922T-F5# | 功能描述:iButton Temp Logger Ibutton w/8Kb Datalog Mem RoHS:否 存儲類型:SRAM 存儲容量:512 B 組織: 工作電源電壓:3 V to 5.25 V 接口類型:1-Wire 最大工作溫度:+ 85 C 尺寸:17.35 mm x 5.89 mm 封裝 / 箱體:F5 MicroCan 制造商:Maxim Integrated |
| DS1922T-F50 | 制造商:Maxim Integrated Products 功能描述:THERMOCHRON,IBTN,F5,HI-TEMP,8K - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。