參數資料
型號: DS18S20Z
元件分類: 溫度傳感器
英文描述: High Precision 1-Wire Digital Thermometer
中文描述: 高精度1 - Wire數字溫度計
文件頁數: 2/27頁
文件大?。?/td> 136K
代理商: DS18S20Z
DS18S20
2 of 27
DETAILED PIN DESCRIPTION
PIN
8-PIN SOIC
TO92
5
4
PIN
SYMBOL
GND
DQ
DESCRIPTION
Ground.
Data Input/Output pin.
For 1-Wire operation: Open drain.
(See “Parasite Power” section.)
Optional V
DD
pin.
See “Parasite Power” section for details of
connection. V
DD
must be grounded for operation in parasite
power mode.
1
2
3
3
V
DD
DS18S20Z (8-pin SOIC): All pins not specified in this table are not to be connected.
OVERVIEW
The block diagram of Figure 1 shows the major components of the DS18S20. The DS18S20 has three
main data components: 1) 64–bit lasered ROM, 2) temperature sensor, 3) nonvolatile temperature alarm
triggers TH and TL. The device derives its power from the 1–Wire communication line by storing energy
on an internal capacitor during periods of time when the signal line is high and continues to operate off
this power source during the low times of the 1–Wire line until it returns high to replenish the parasite
(capacitor) supply. As an alternative, the DS18S20 may also be powered from an external 3 volt – 5 volt
supply.
Communication to the DS18S20 is via a 1–Wire port. With the 1–Wire port, the memory and control
functions will not be available before the ROM function protocol has been established. The master must
first provide one of five ROM function commands: 1) Read ROM, 2) Match ROM, 3) Search ROM, 4)
Skip ROM, or 5) Alarm Search. These commands operate on the 64–bit lasered ROM portion of each
device and can single out a specific device if many are present on the 1–Wire line as well as indicate to
the bus master how many and what types of devices are present. After a ROM function sequence has
been successfully executed, the memory and control functions are accessible and the master may then
provide any one of the six memory and control function commands.
One control function command instructs the DS18S20 to perform a temperature measurement. The result
of this measurement will be placed in the DS18S20’s scratch-pad memory, and may be read by issuing a
memory function command which reads the contents of the scratchpad memory. The temperature alarm
triggers TH and TL consist of 1-byte EEPROM each. If the alarm search command is not applied to the
DS18S20, these registers may be used as general purpose user memory. Writing TH and TL is done
using a memory function command. Read access to these registers is through the scratchpad. All data is
read and written least significant bit first.
相關PDF資料
PDF描述
DS1923 Hygrochron Temperature/Humidity Logger iButton with 8kB Data Log Memory
DS1923-F5 Hygrochron Temperature/Humidity Logger iButton with 8kB Data Log Memory
DS1990 Serial Number iButton
DS1990A Serial Number iButton
DS1990A-F5 Serial Number iButton
相關代理商/技術參數
參數描述
DS18S20Z/T&R 制造商:Maxim Integrated Products 功能描述:HI PREC MICROLAN DIG THERM 8-SO T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERM MICROLAN HI-PREC 8-SOIC
DS18S20Z/T&R 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
DS18S20Z+ 功能描述:板上安裝溫度傳感器 Prgmble Resolution 1-Wire Parasite Pwr RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
DS18S20Z+T&R 制造商:Maxim Integrated Products 功能描述:TEMP SENSOR DGTL 1-WIRE 8SOIC - Tape and Reel 制造商:Maxim Integrated Products 功能描述:HI PREC MICROLAN DIG THERM 8-SO T&R 制造商:Maxim Integrated Products 功能描述:IC THERM MICROLAN HI-PREC 8SOIC 制造商:Maxim Integrated Products 功能描述:IC THERM MICROLAN HI-PREC 8-SOIC 制造商:Maxim Integrated Products 功能描述:Board Mount Temperature Sensors Prgmble Resolution 1-Wire Parasite Pwr
DS18S20Z+T&R 功能描述:板上安裝溫度傳感器 Prgmble Resolution 1-Wire Parasite Pwr RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor