參數資料
型號： DS18S20Z
元件分類： 溫度傳感器
英文描述： High Precision 1-Wire Digital Thermometer
中文描述： 高精度1 - Wire數字溫度計
文件頁數： 13/27頁
文件大?。?/td> 136K
代理商： DS18S20Z
DS18S20
13 of 27
The initialization sequence required to begin any communication with the DS18S20 is shown in Figure
10. A reset pulse followed by a presence pulse indicates the DS18S20 is ready to send or receive data
given the correct ROM command and memory function command.
The bus master transmits (TX) a reset pulse (a low signal for a minimum of 480 ms). The bus master
then releases the line and goes into a receive mode (RX). The 1–Wire bus is pulled to a high state via the
5k pullup resistor. After detecting the rising edge on the DQ pin, the DS18S20 waits 15–60
μ
s and then
transmits the presence pulse (a low signal for 60–240
μ
s).
MEMORY COMMAND FUNCTIONS
The following command protocols are summarized in Table 2, and by the flowchart of Figure 9.
Write Scratchpad [4Eh]
This command writes to the scratchpad of the DS18S20, starting at the TH register. The next 2 bytes
written will be saved in scratchpad memory at address locations 2 and 3. Writing may be terminated at
any point by issuing a reset.
Read Scratchpad [BEh]
This command reads the contents of the scratchpad. Reading will commence at byte 0, and will continue
through the scratchpad until the ninth (byte 8, CRC) byte is read. If not all locations are to be read, the
master may issue a reset to terminate reading at any time.
Copy Scratchpad [48h]
This command copies the scratchpad into the E
2
memory of the DS18S20, storing the temperature trigger
bytes in nonvolatile memory. If the bus master issues read time slots following this command, the
DS18S20 will output 0 on the bus as long as it is busy copying the scratchpad to E
2
; it will return a 1
when the copy process is complete. If parasite-powered, the bus master has to enable a strong pullup for
at least 10 ms immediately after issuing this command. The DS18S20 EEPROM is rated for a minimum
of 50,000 writes and 10 years data retention at T = +55°C.
Convert T [44h]
This command begins a temperature conversion. No further data is required. The temperature
conversion will be performed and then the DS18S20 will remain idle. If the bus master issues read time
slots following this command, the DS18S20 will output 0 on the bus as long as it is busy making a
temperature conversion; it will return a 1 when the temperature conversion is complete. If parasite-
powered, the bus master has to enable a strong pullup for a time period greater than t
conv
immediately
after issuing this command.
Recall E2 [B8h]
This command recalls the temperature trigger values stored in E
2
to the scratchpad. This recall operation
happens automatically upon power–up to the DS18S20 as well, so valid data is available in the scratchpad
as soon as the device has power applied. With every read data time slot issued after this command has
been sent, the device will output its temperature converter busy flag: 0=busy, 1=ready.
Read Power Supply [B4h]
With every read data time slot issued after this command has been sent to the DS18S20, the device will
signal its power mode: 0=parasite power, 1=external power supply provided.
相關PDF資料
PDF描述
DS1923 Hygrochron Temperature/Humidity Logger iButton with 8kB Data Log Memory
DS1923-F5 Hygrochron Temperature/Humidity Logger iButton with 8kB Data Log Memory
DS1990 Serial Number iButton
DS1990A Serial Number iButton
DS1990A-F5 Serial Number iButton
相關代理商/技術參數
參數描述
DS18S20Z/T&R 制造商:Maxim Integrated Products 功能描述:HI PREC MICROLAN DIG THERM 8-SO T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERM MICROLAN HI-PREC 8-SOIC
DS18S20Z/T&R 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
DS18S20Z+ 功能描述:板上安裝溫度傳感器 Prgmble Resolution 1-Wire Parasite Pwr RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
DS18S20Z+T&R 制造商:Maxim Integrated Products 功能描述:TEMP SENSOR DGTL 1-WIRE 8SOIC - Tape and Reel 制造商:Maxim Integrated Products 功能描述:HI PREC MICROLAN DIG THERM 8-SO T&R 制造商:Maxim Integrated Products 功能描述:IC THERM MICROLAN HI-PREC 8SOIC 制造商:Maxim Integrated Products 功能描述:IC THERM MICROLAN HI-PREC 8-SOIC 制造商:Maxim Integrated Products 功能描述:Board Mount Temperature Sensors Prgmble Resolution 1-Wire Parasite Pwr
DS18S20Z+T&R 功能描述:板上安裝溫度傳感器 Prgmble Resolution 1-Wire Parasite Pwr RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*