參數資料
型號： DS1862AB+
廠商： MAXIM INTEGRATED PRODUCTS INC
元件分類： 消費家電
英文描述： SPECIALTY CONSUMER CIRCUIT, PBGA25
封裝： 5 X 5 MM, ROHS COMPLIANT, CSBGA-25
文件頁數： 35/42頁
文件大小： 586K
代理商： DS1862AB+
DS1862A
XFP Laser Control and Digital Diagnostic IC
40
______________________________________________________________________________________
CRC-8 includes and requires the explicit starting mem-
ory address to be included as the second transferred
byte. Next, the master transfers the data as the
DS1862A acknowledges. Only 4 bytes can be sequen-
tially written during one transmission while using PEC.
After the master writes the intended number of bytes,
the CRC-8 value should be transmitted. Following the
CRC-8 byte, the master should transmit the CAB byte
(CRC Add-on Byte). At this point, the DS1862A sends
an ACK if the CRC-8 matches its internal calculated
value or a NACK if not. Finally, the master should end
the communication and send a STOP. See Figure 16 for
a graphical representation. The CRC-8 is calculated
starting with the MSB of the memory address pointer,
number of bytes to be written, and the written data. The
master can then poll the last ACK or NACK for suc-
cessful transfer of written data.
For more information on I2C PEC communications, refer
to the XFP and/or SMBus 2.0 standard.
Applications Information
Calibrating APC and Extinction Ratio
Before calibrating, the APC register should be set to a
low value to ensure the laser’s maximum power level is
not exceeded before the power level is calibrated.
Additionally, the ER should be set to a minimum value
to ensure that a data test pattern does not cause the
laser to shut off. Once the APC and ER registers are at
minimal values, enable a data pattern and calibrate the
average power level.
Calibrating the Average Power Level
While sending data through the laser diode, increase
the value in the APC register until the light output
matches the desired
average power level. The average
power level is the arithmetic average of the ‘1’ and ‘0’
power levels.
XXXXXXXX
10
1
0
10
1
0
10
1
0
COMMUNICATIONS KEY
WRITE UP TO A 4-BYTE PAGE WITH A SINGLE TRANSACTION USING PEC
READ 1–128 BYTES WITH A DUMMY WRITE CYCLE TO SET THE ADDRESS COUNTER
8-BIT ADDRESS OR DATA
WHITE BOXES INDICATE THE MASTER IS
CONTROLLING SDA
THE FIRST BYTE SENT AFTER A START CONDITION IS
ALWAYS THE SLAVE ADDRESS FOLLOWED BY THE
READ/WRITE BIT.
SHADED BOXES INDICATE THE SLAVE IS
CONTROLLING SDA
START
ACK
NOT
ACK
S
A
SR
A
N
P
A
CRC-8 VALUE
DATA
CRC-8 VALUE
DATA
MEMORY ADDRESS
A
NUMBER OF BYTES
MEMORY ADDRESS
DATA
AA
A
PN
SR
STOP
REPEATED
START
NOTE:
ALL BYTES ARE SENT MOST SIGNIFICANT BIT FIRST.
A (IF CRC-8 IS CORRECT)
P
DATA
Figure 16. I2C PEC Communications Examples
相關PDF資料
PDF描述
DS1862AB+T&R SPECIALTY CONSUMER CIRCUIT, PBGA25
DS1868-100-IND 100K DIGITAL POTENTIOMETER, 2-WIRE SERIAL CONTROL INTERFACE, 256 POSITIONS, PDIP14
DS2-320-2AR DIP20, IC SOCKET
DS1-314-1AR DIP14, IC SOCKET
DS3-328-1AR DIP28, IC SOCKET
相關代理商/技術參數
參數描述
DS1862AB+ 功能描述:激光驅動器 XFP Laser Control & Digital Diagnostic RoHS:否 制造商:Micrel 數據速率:4.25 Gbps 工作電源電壓:3 V to 3.6 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-16 封裝:Tube
DS1862AB+T&R 制造商:Maxim Integrated Products 功能描述:XFP LASER CONTROL 25CSBGA - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC LASR CTRLR 7CHAN 5.5V 25CSBGA
DS1862AB+T&R 功能描述:激光驅動器 XFP Laser Control & Digital Diagnostic RoHS:否 制造商:Micrel 數據速率:4.25 Gbps 工作電源電壓:3 V to 3.6 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-16 封裝:Tube
DS1862AB+TR 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:XFP Laser Control and Digital Diagnostic IC
DS1862B 功能描述:激光驅動器 RoHS:否 制造商:Micrel 數據速率:4.25 Gbps 工作電源電壓:3 V to 3.6 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-16 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*