- 您現在的位置：買賣IC網 > PDF目錄9048 > DS1858B-050 (Maxim Integrated Products)IC RES TEMP 50/50K W/3MON 16-BGA PDF資料下載
參數資料
| 型號： | DS1858B-050 |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 11/22頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC RES TEMP 50/50K W/3MON 16-BGA |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 810 |
| 接片： | 256 |
| 電阻（歐姆）： | 50k |
| 電路數： | 2 |
| 溫度系數： | 標準值 50 ppm/°C |
| 存儲器類型： | 非易失 |
| 接口： | I²C（設備位址） |
| 電源電壓： | 3 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 95°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-LBGA，CSPBGA |
| 供應商設備封裝： | 16-CSBGA（4x4） |
| 包裝： | 托盤 |
DS1858
Dual Temperature-Controlled
Resistors with Three Monitors
____________________________________________________________________
19
section). If the address does not match, this part
returns to a low-power mode.
Write Operations
After receiving a matching address byte with the R/W
bit set low, provided there is no write protect, the
device goes into the write mode of operation (see the
Memory Organization section). The master must trans-
mit an 8-bit EEPROM memory address to the device to
define the address where the data is to be written. After
the byte has been received, the DS1858 transmits a
zero for one clock cycle to acknowledge the address
has been received. The master must then transmit an
8-bit data word to be written into this address. The
DS1858 again transmits a zero for one clock cycle to
acknowledge the receipt of the data. At this point, the
master must terminate the write operation with a stop
condition. The DS1858 then enters an internally timed
write process tw to the EEPROM memory. All inputs are
disabled during this byte write cycle.
Page Write
The DS1858 is capable of an 8-byte page write. A page
is any 8-byte block of memory starting with an address
evenly divisible by eight and ending with the starting
address plus seven. For example, addresses 00h
through 07h constitute one page. Other pages would
be addresses 08h through 0Fh, 10h through 17h, 18h
through 1Fh, etc.
A page write is initiated the same way as a byte write,
but the master does not send a STOP condition after
the first byte. Instead, after the slave acknowledges the
data byte has been received, the master can send up
to seven more bytes using the same nine-clock
sequence. The master must terminate the write cycle
with a STOP condition or the data clocked into the
DS1858 will not be latched into permanent memory.
The address counter rolls on a page during a write. The
counter does not count through the entire address
space as during a read. For example, if the starting
address is 06h and 4 bytes are written, the first byte
goes into address 06h. The second goes into address
07h. The third goes into address 00h (not 08h). The
fourth goes into address 01h. If more than 9 bytes or
more are written before a STOP condition is sent, the
first bytes sent are overwritten. Only the last 8 bytes of
data are written to the page.
Acknowledge Polling: Once the internally timed write
has started and the DS1858 inputs are disabled,
acknowledge polling can be initiated. The process
involves transmitting a start condition followed by the
device address. The R/W bit signifies the type of opera-
tion that is desired. The read or write sequence will only
be allowed to proceed if the internal write cycle has
completed and the DS1858 responds with a zero.
Read Operations
After receiving a matching address byte with the R/W bit
set high, the device goes into the read mode of opera-
tion. There are three read operations: current address
read, random read, and sequential address read.
Current Address Read
The DS1858 has an internal address register that main-
tains the address used during the last read or write
operation, incremented by one. This data is maintained
as long as VCC is valid. If the most recent address was
the last byte in memory, then the register resets to the
first address.
Once the device address is clocked in and acknowl-
edged by the DS1858 with the R/W bit set to high, the
current address data word is clocked out. The master
does not respond with a zero, but does generate a stop
condition afterwards.
Single Read
A random read requires a dummy byte write sequence to
load in the data byte address. Once the device and data
address bytes are clocked in by the master, and
acknowledged by the DS1858, the master must generate
another start condition. The master now initiates a current
address read by sending the device address with the
R/W bit set high. The DS1858 acknowledges the device
address and serially clocks out the data byte.
Sequential Address Read
Sequential reads are initiated by either a current
address read or a random address read. After the mas-
ter receives the first data byte, the master responds
with an acknowledge. As long as the DS1858 receives
this acknowledge after a byte is read, the master can
clock out additional data words from the DS1858. After
reaching address FFh, it resets to address 00h.
The sequential read operation is terminated when the
master initiates a stop condition. The master does not
respond with a zero.
For a more detailed description of 2-wire theory of
operation, see the following section.
2-Wire Serial Port Operation
The 2-wire serial port interface supports a bidirectional
data transmission protocol with device addressing. A
device that sends data on the bus is defined as a trans-
mitter, and a device receiving data as a receiver. The
device that controls the message is called a master.
The devices that are controlled by the master are
相關PDF資料 |
PDF描述 |
|---|---|
| DS1869S-010+T&R | IC RHEOSTAT DALLAST 3V 10K 8SOIC |
| VI-B5Y-MW-F3 | CONVERTER MOD DC/DC 3.3V 66W |
| VI-B5Y-MW-F2 | CONVERTER MOD DC/DC 3.3V 66W |
| VE-JWJ-MZ-F3 | CONVERTER MOD DC/DC 36V 25W |
| VI-B5X-MY-F3 | CONVERTER MOD DC/DC 5.2V 50W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1858B-050+ | 功能描述:數字電位計 IC Dual Temp-Controlled Resistors RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| DS1858E-050 | 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| DS1858E-050/R | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Dual Temperature-Controlled Resistors with Three Monitors |
| DS1858E-050/T | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Dual Temperature-Controlled Resistors with Three Monitors |
| DS1858E-050/T&R | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Dual Temperature-Controlled Resistors with Three Monitors |
發(fā)布緊急采購，3分鐘左右您將得到回復。