- 您現在的位置：買賣IC網 > PDF目錄1913 > DS1846E-010+T&R (Maxim Integrated Products)IC NV TRI-POT MEM MON 20TSSOP PDF資料下載
參數資料
| 型號： | DS1846E-010+T&R |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 15/18頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC NV TRI-POT MEM MON 20TSSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 接片： | 100，256 |
| 電阻（歐姆）： | 10k，100k |
| 電路數： | 3 |
| 溫度系數： | 標準值 750 ppm/°C |
| 存儲器類型： | 非易失 |
| 接口： | 3 線串行（設備位址） |
| 電源電壓： | 4.5 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 20-TSSOP |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁
DS1846
6 of 18
DS1846 is not latched into EEPROM. Note that in order for eight bytes to be stored sequentially (and to
prevent looping around), the address byte must be set to the beginning of the desired page (three LSBs of
the address are 0). For detailed information concerning page operations, see the MEMORY
ORGANIZATION section.
The DS1846 is capable of an 8-byte page write. A page write is initiated the same way as a byte write, but
the master does not send a stop condition after the first data byte. Instead, after the slave acknowledges
receipt of the data byte, the master can send up to seven more data bytes using the same nine-clock
sequence. After a write to the last byte in the page, the address returns to the beginning of the page. The
master must terminate the write cycle with a stop condition or the data clocked into the DS1846 is not
latched into permanent memory.
Acknowledge Polling: Once the internally timed write has started and the DS1846 inputs are disabled,
acknowledge polling can be initiated. The process involves transmitting a start condition followed by the
device address. The R/W bit signifies the type of operation that is desired. The read or write sequence is
only allowed to proceed if the internal write cycle has completed and the DS1846 responds with a zero.
Read Operations: After receiving a matching address byte with the R/W bit set high, the device goes
into the read mode of operation. There are three read operations: current address read, random read, and
sequential address read.
CURRENT ADDRESS READ
The DS1846 has an internal address register that maintains the address used during the last read or write
operation, incremented by one. This data is maintained as long as VCC is valid. If the most recent address
was the last byte in memory, then the register resets to the first address. This address stays valid between
operations as long as power is available.
Once the device address is clocked in and acknowledged by the DS1846 with the R/W bit set to high, the
current address data word is clocked out. The master does not respond with a zero, but does generate a
stop condition afterwards.
RANDOM READ
A random read requires a dummy byte write sequence to load in the data word address. Once the device
address and data bytes are clocked in by the master, and acknowledged by the DS1846, the master must
generate another start condition. The master now initiates a current address read by sending the device
address with the R/W bit set high. The DS1846 acknowledges the device address and serially clocks out
the data byte.
SEQUENTIAL ADDRESS READ
Sequential reads are initiated by either a current address read or a random address read. After the master
receives the first data byte, the master responds with an acknowledge. As long as the DS1846 receives
this acknowledge after a byte is read, the master may clock out additional data words from the DS1846.
After reaching address FFh, it resets to address 00h.
The sequential read operation is terminated when the master initiates a stop condition. The master does
not respond with a zero.
For a more detailed description of 2-wire theory of operation, see the following section.
相關PDF資料 |
PDF描述 |
|---|---|
| DS1847E-010/T&R | IC RES TEMP-CNTRL 10/10K 14TSSOP |
| DS1848B-C10+ | IC RES/MEM TEMP 10/10K 16-CSBGA |
| DS1852B-000/T&R | IC MONITOR TXRX OPTICAL 25-BGA |
| DS1852B-00C+ | IC MONITOR TXRX OPTICAL 25-BGA |
| DS1854E-050 | IC RES TEMP-CNTRL 50/50K 16TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1847 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Dual Temperature-Controlled NV Variable Resistor |
| DS1847-010 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Dual Temperature-Controlled NV Variable Resistor |
| DS1847-050 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Dual Temperature-Controlled NV Variable Resistor |
| DS1847B-010 | 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| DS1847B-010/T&R | 制造商:Maxim Integrated Products 功能描述:DUAL NV TEMP CNTRL VAR RES 10/10K T - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。