- 您現在的位置：買賣IC網 > PDF目錄358701 > DS1831S (MAXIM INTEGRATED PRODUCTS INC) Multisupply Micromonitor PDF資料下載
參數資料
| 型號： | DS1831S |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | Multisupply Micromonitor |
| 中文描述： | 4-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16 |
| 封裝： | 0.150 INCH, SOIC-16 |
| 文件頁數： | 9/14頁 |
| 文件大?。?/td> | 206K |
| 代理商： | DS1831S |
DS1831/A/B
9 of 14
NON-MASKABLE INTERRUPT CIRCUIT EXAMPLE
Figure 9
Example:
V
SENSE1
= 11.50V trip point
V
SENSE1
=
R2
R2
R1
X 1.25V
Therefore:
11.50V =
k
100
k
100
R1
X 1.25V
Resulting In: R1 = 820k
Repeat the same steps to solve for R3 and R4 with V
SENSE2
.
OPERATION - WATCHDOG TIMER
The watchdog timer function (DS1831A only) forces the
WDS
signal active (low) when the
ST
input
does not have a transition (high-to-low or low-to-high) within the predetermined time period. The time-
out period is determined by the condition of the TD
WD
pin (see Table 1). If TD
WD
is connected to ground
the minimum watchdog time-out would be 10ms, TD floating would yield a minimum time-out of 100ms,
and TD
WD
connected to V
CC
would provide a time-out of 1000ms minimum. Time-out of the watchdog
starts when at least one of the
RST
outputs becomes inactive (high). If a transition occurs on the ST input
pin prior to time-out, the watchdog timer is reset and begins to time-out again. If the watchdog timer is
allowed to time-out, then the
WDS
output is pulsed active for a minimum of 100μs.
The
WDS
output is an open-drain output and must be pulled up externally. In most applications this
output would be connected to one of the Pushbutton inputs and would not require an external pull-up
resistor. The value of the resistors is not critical in most cases but must be set low enough to pull the
output to a high state. A common value used is 10k . If a
WDS
output is connected to a pushbutton input
an additional pull-up resistor can be used (to improve speed of transitions) but is not required.
R1
DS1831
GND
IN1
V
SENSE1
R2
IN2
R3
V
SENSE2
R4
V
CC
10 K
PBRST
5V
PBRST
3.3V
NMI1
NMI2
MPBRST
相關PDF資料 |
PDF描述 |
|---|---|
| DS1856E-025R | Dual, Temperature-Controlled Resistors with Internally Calibrated Monitors and Password Protection |
| DS1922L | Temperature Logger iButton with 8kB Datalog Memory |
| DS1922T | Temperature Logger iButton with 8kB Datalog Memory |
| DS1922L-F5 | Temperature Logger iButton With 8kB Datalog Memory |
| DS1992 | 1kb/4kb Memory iButton |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1831S/T&R | 制造商:Maxim Integrated Products 功能描述:MULTISUPPLY MONITOR 16P SOIC T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC MULTIMON 5V/3.3V 16-SOIC |
| DS1831S/T&R | 功能描述:監控電路 3.3/5V Multisupply MicroMonitor RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| DS1831S+ | 功能描述:監控電路 3.3/5V Multisupply MicroMonitor RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| DS1831S+T&R | 制造商:Maxim Integrated Products 功能描述:PROCESSOR SUPERVISOR 4.63V/3.06V 100UA 16SOIC - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC MULTIMON 5V/3.3V 16-SOIC |
| DS1831S+T&R | 功能描述:監控電路 3.3/5V Multisupply MicroMonitor RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。