參數資料
型號: DS1831S
廠商: MAXIM INTEGRATED PRODUCTS INC
元件分類: 電源管理
英文描述: Multisupply Micromonitor
中文描述: 4-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16
封裝: 0.150 INCH, SOIC-16
文件頁數: 4/14頁
文件大?。?/td> 206K
代理商: DS1831S
DS1831/A/B
4 of 14
PUSHBUTTON RESET SEQUENCING
Figure 2
NOTE: The
RST
5V
output is connected to the IN
3.3V
via a 100 k resistor in the push-button input and
therefore does not require a pull-up resistor (an addition pull up can be used to accelerate responses). If an
external pull up is used in this example it must be connected to the 3.3V power supply.
OPERATION—PUSHBUTTON RESET
The DS1831 provides three pushbutton inputs for manual reset of the device. Pushbutton inputs for the
3.3V reset, 5V reset, and a master pushbutton reset (DS1831 and DS1831B only) input; provide multiple
options for system control. The 3.3V pushbutton reset and 5V pushbutton resets provide a simple manual
reset for the associated reset output; while the master pushbutton reset forces all resets and NMI outputs
active low.
The 5V reset pushbutton input and the 3.3V reset pushbutton input provide manual reset control input for
each associated reset output. When the output associated with a pushbutton input is not active, a
pushbutton reset can be generated by pulling the associated
PBRST
pin low for at least 20μs. When the
pushbutton is held low the reset will be forced active and will remain active for a reset cycle after the
pushbutton is released. See Figure 2 for an application example that allows a user to sequence the reset
outputs.
A master pushbutton reset cycle can be started if at least one voltage input (IN
5V
, IN
3.3V
, IN1, or IN2) is in
tolerance and at least one output is active. A master pushbutton reset is generated by pulling the
MPBRST
pin low for at least 20μs. When the pushbutton is held low all outputs are forced active and will remain
active for a reset or NMI time delay after the pushbutton is released. The Master Pushbutton input is
pulled high through an internal 100k pull up resistor and debounced via internal circuitry. See Figure 3
for an application example. Figures 4 and 5 for the timing diagram.
The 5V and 3.3V pushbutton reset inputs are pulled high through an internal 100k pull up resistor to the
voltage input, which is associated with that pushbutton. The master pushbutton is pulled to the greater of
the IN
5V
and IN
3.3V
inputs.
RST
5V
PBRST
3.3V
GND
TD
5V
IN
3.3V
IN
5V
RST
3.3V
TOL
3.3V
PBRST
5V
TOL
5V
DS1831
TD
3.3V
5V Supply
3.3V Supply
1
2
3
4
5
16
15
14
13
12
相關PDF資料
PDF描述
DS1856E-025R Dual, Temperature-Controlled Resistors with Internally Calibrated Monitors and Password Protection
DS1922L Temperature Logger iButton with 8kB Datalog Memory
DS1922T Temperature Logger iButton with 8kB Datalog Memory
DS1922L-F5 Temperature Logger iButton With 8kB Datalog Memory
DS1992 1kb/4kb Memory iButton
相關代理商/技術參數
參數描述
DS1831S/T&R 制造商:Maxim Integrated Products 功能描述:MULTISUPPLY MONITOR 16P SOIC T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC MULTIMON 5V/3.3V 16-SOIC
DS1831S/T&R 功能描述:監控電路 3.3/5V Multisupply MicroMonitor RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲(典型值):10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
DS1831S+ 功能描述:監控電路 3.3/5V Multisupply MicroMonitor RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲(典型值):10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
DS1831S+T&R 制造商:Maxim Integrated Products 功能描述:PROCESSOR SUPERVISOR 4.63V/3.06V 100UA 16SOIC - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC MULTIMON 5V/3.3V 16-SOIC
DS1831S+T&R 功能描述:監控電路 3.3/5V Multisupply MicroMonitor RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲(典型值):10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel