- 您現在的位置：買賣IC網 > PDF目錄385272 > DS1825U (MAXIM INTEGRATED PRODUCTS INC) Programmable Resolution 1-Wire Digital Thermometer With 4-Bit ID PDF資料下載
參數資料
| 型號： | DS1825U |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | Programmable Resolution 1-Wire Digital Thermometer With 4-Bit ID |
| 中文描述： | SPECIALTY ANALOG CIRCUIT, PDSO8 |
| 封裝： | MICRO SOP-8 |
| 文件頁數： | 17/21頁 |
| 文件大?。?/td> | 298K |
| 代理商： | DS1825U |
DS1825 Programmable Resolution 1-Wire Digital Thermometer With 4-Bit ID
Figure 15. READ/WRITE TIME SLOT TIMING DIAGRAM
READ TIME SLOTS
The DS1825 can only transmit data to the master when the master issues read time slots. Therefore, the master
must generate read time slots immediately after issuing a Read Scratchpad [BEh] or Read Power Supply [B4h]
command, so that the DS1825 can provide the requested data. In addition, the master can generate read time slots
after issuing Convert T [44h] or Recall E
[B8h] commands to find out the status of the operation as explained in
the DS1825 FUNCTION COMMAND section.
All read time slots must be a minimum of 60 s in duration with a minimum of a 1 s recovery time between slots. A
read time slot is initiated by the master device pulling the 1-Wire bus low for a minimum of 1 s and then releasing
the bus (see Figure 14). After the master initiates the read time slot, the DS1825 will begin transmitting a 1 or 0 on
bus. The DS1825 transmits a 1 by leaving the bus high and transmits a 0 by pulling the bus low. When transmitting
a 0, the DS1825 will release the bus by the end of the time slot, and the bus will be pulled back to its high idle state
by the pullup resister. Output data from the DS1825 is valid for 15 s after the falling edge that initiated the read
time slot. Therefore, the master must release the bus and then sample the bus state within 15 s from the start of
the slot.
17 of 21
Figure 15 illustrates that the sum of T
INIT
, T
RC
, and T
SAMPLE
must be less than 15 s for a read time slot. Figure 16
shows that system timing margin is maximized by keeping T
INIT
and T
RC
as short as possible and by locating the
master sample time during read time slots towards the end of the 15 s period.
45 s
15 s
V
PU
GND
1-WIRE BUS
60 s < T
X
“0” < 120 s
1 s < T
REC
<
DS1825
Samples
MIN TYP MAX
15 s
30 s
> 1 s
MASTER WRITE “0” SLOT
MASTER WRITE “1” SLOT
V
PU
GND
1-WIRE BUS
15 s
MASTER READ “0” SLOT
MASTER READ “1” SLOT
Master samples
Master samples
START
OF SLOT
START
OF SLOT
> 1 s
1 s < T
REC
<
15 s
15 s
30 s
15 s
DS1825
Samples
MIN TYP MAX
LINE TYPE LEGEND
Bus master pulling low
Resistor pullup
DS1825 pulling low
> 1 s
相關PDF資料 |
PDF描述 |
|---|---|
| DS1825UTR | Programmable Resolution 1-Wire Digital Thermometer With 4-Bit ID |
| DS1830 | Programmable MicroMonitor(可編程微監控器) |
| DS1832 | 3.3 Volt MicroMonitor Chip(3.3 V微監控芯片) |
| DS1833 | 5V EconoReset(5V Econo監控芯片) |
| DS1834 | Dual EconoReset with Pushbutton(帶復位按鈕的雙路Econo復位電路) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1825U/T&R | 制造商:Maxim Integrated Products 功能描述:1-W PROGRAMMABLE DGT THERM 8P USOP - Tape and Reel |
| DS1825U/T&R | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS1825U/TR | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Programmable Resolution 1-Wire Digital Thermometer With 4-Bit ID |
| DS1825U+ | 功能描述:板上安裝溫度傳感器 Prog Resolution 1-Wire w/4-Bit ID RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS1825U+ | 制造商:Maxim Integrated Products 功能描述:IC THERMOMETER 12BIT ?0.5 ?SOP-8 制造商:Maxim Integrated Products 功能描述:IC, THERMOMETER, 12BIT, 0.5C, ?SOP-8 |
發布緊急采購，3分鐘左右您將得到回復。