- 您現在的位置：買賣IC網 > PDF目錄9184 > DS1805E-010+T&R (Maxim Integrated Products)IC POT DIG ADDRESS 10K 14-TSSOP PDF資料下載
參數資料
| 型號： | DS1805E-010+T&R |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 8/10頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC POT DIG ADDRESS 10K 14-TSSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1,000 |
| 接片： | 256 |
| 電阻（歐姆）： | 10k |
| 電路數： | 1 |
| 溫度系數： | 標準值 550 ppm/°C |
| 存儲器類型： | 易失 |
| 接口： | I²C（設備位址） |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 14-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 14-TSSOP |
| 包裝： | 帶卷 (TR) |
DS1805
Addressable Digital Potentiometer
_____________________________________________________________________
7
The potentiometer is composed of a 256-position resis-
tor array. Two 8-bit registers are provided to ensure
compatibility with DS1803-based designs. Register-0 is
a general-purpose SRAM byte, while register-1 is
assigned to the potentiometer and is used to set the
wiper position on the resistor array. The wiper terminal
is multiplexed to one of 256 positions on the resistor array
based on its corresponding 8-bit register value. The high-
est wiper setting, FFh, is 1 LSB away from H1 (resistor
255), while the lowest setting, 00h, connects to L1.
The DS1805 is a volatile device that does not maintain
the position of the wiper during power-down or loss of
power. On power-up, the wiper position is set to 00h
(the low-end terminal). The user can then set the wiper
value to a desired position.
Communication with the DS1805 takes place over the
2-wire serial interface consisting of the bidirectional
data terminal, SDA, and the serial clock input, SCL.
Complete details of the 2-wire interface are discussed
in the 2-Wire Serial Data Bus section.
The 2-wire interface and address inputs A0, A1, and A2
allow operation of up to eight devices in a bus topology,
with A0, A1, and A2 being the address of the device.
Application Considerations
The DS1805 is offered in three standard resistor values:
10k
, 50k, and 100k. The resolution of the poten-
tiometer is defined as RTOT/256, where RTOT is the total
resistor value of the potentiometer. The DS1805 is
designed to operate using 3V or 5V power supplies over
the industrial (-40°C to +85°C) temperature range.
Maximum input signal levels across the potentiometer
cannot exceed the operating power supply of the device.
2-Wire Serial Data Bus
The DS1805 supports a bidirectional 2-wire bus and
data transmission protocol. A device that sends data on
the bus is called a transmitter, and a device receiving
data is called a receiver. The device that controls the
message is called a master. The devices that are con-
trolled by the master are slaves. The bus must be con-
trolled by a master device that generates the serial
clock (SCL), controls the bus access, and generates the
START and STOP conditions. The DS1805 operates as
a slave on the 2-wire bus. Connections to the bus are
made through the open-drain I/O lines, SDA and SCL.
The following bus protocol has been defined (Figure 2):
Data transfer can be initiated only when the bus is
not busy.
During data transfer, the data line must remain sta-
ble whenever the clock line is high. Changes in the
data line while the clock line is high will be interpret-
ed as control signals.
Accordingly, the following bus conditions have been
defined:
Bus not busy: Both data and clock lines remain high.
Start data transfer: A change in the state of the data
line from high to low while the clock is high defines a
START condition.
STOP
CONDITION
OR REPEATED
START
CONDITION
REPEATED IF MORE BYTES
ARE TRANSFERED
ACK
START
CONDITION
ACK
ACKNOWLEDGEMENT
SIGNAL FROM RECEIVER
ACKNOWLEDGEMENT
SIGNAL FROM RECEIVER
SLAVE ADDRESS
MSB
SCL
SDA
R/W
DIRECTION
BIT
12
6
7
8
9
1
2
8
9
3–7
Figure 2. 2-Wire Data Transfer Overview
相關PDF資料 |
PDF描述 |
|---|---|
| VI-BWZ-MW-F2 | CONVERTER MOD DC/DC 2V 40W |
| VI-BWZ-MW-F1 | CONVERTER MOD DC/DC 2V 40W |
| MAX5388MAUB+ | IC DGTL POT 256POS 50K 10UMAX |
| VI-B5V-MW-B1 | CONVERTER MOD DC/DC 5.8V 100W |
| VI-BWY-MY-F4 | CONVERTER MOD DC/DC 3.3V 33W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1805E-050 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Addressable Digital Potentiometer |
| DS1805E-100 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Addressable Digital Potentiometer |
| DS1805F-010 | 制造商:Maxim Integrated Products 功能描述:SINGLE DIGITAL POTENTIOMETER - Rail/Tube |
| DS1805Z-010 | 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| DS1805Z-010+ | 功能描述:數字電位計 IC Addressable RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。