- 您現在的位置：買賣IC網 > PDF目錄9058 > DS18030-100 (Maxim Integrated Products)IC POT DUAL ADDRESS 100K 16-DIP PDF資料下載
參數資料
| 型號： | DS18030-100 |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 10/11頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC POT DUAL ADDRESS 100K 16-DIP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 25 |
| 接片： | 256 |
| 電阻（歐姆）： | 100k |
| 電路數： | 2 |
| 溫度系數： | 標準值 750 ppm/°C |
| 存儲器類型： | 易失 |
| 接口： | I²C（芯片選擇） |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 通孔 |
| 封裝/外殼： | 16-DIP（0.300"，7.62mm） |
| 供應商設備封裝： | 16-PDIP |
| 包裝： | 管件 |
DS1803
8 of 11
5. After this period, the first clock pulse is generated.
6. A device must internally provide a hold time of at least 300 ns for the SDA signal (referred to the
VIHMIN of the SCL signal) in order to bridge the undefined region of the falling edge of SCL.
7. The maximum tHD:DAT has only to be met if the device does not stretch the LOW period (tLOW) of the
SCL signal.
8. A fast mode device can be used in a standard mode system, but the requirement tSU:DAT > 250 ns must
then be met. This will automatically be the case if the device does not stretch the LOW period of the
SCL signal. If such a device does stretch the LOW period of the SCL signal, it must output the next
data bit to the SDA line tRMAX+ tSU:DAT = 1000 + 250=1250 ns before the SCL line is released.
9. CB - total capacitance of one bus line in picofarads, timing referenced to (0.9)(VCC) and (0.1)(VCC).
10. Typical values are for tA = 25°C and nominal supply voltage.
11. -3 dB cutoff frequency characteristics for the DS1803 depend on potentiometer total resistance:
DS1803-010; 1 MHz, DS1803-50; 200 kHz, DS1803-100; 100 kHz.
12. Address Inputs, A0, A1, and A2, should be tied to either VCC or GND depending on the desired
address selections.
13. Absolute linearity is used to determine wiper voltage versus expected voltage as determined by wiper
position. Device test limits are
±1.6 LSB.
14. Relative linearity is used to determine the change in voltage between successive tap positions. Device
test limits
±0.5 LSB.
15. Fast mode.
16. Standard mode.
17. Valid at 25
°C only.
相關PDF資料 |
PDF描述 |
|---|---|
| SL15100ZIT | IC CLOCK SSCG 1PLL 2CH 8TSSOP |
| MK2308G-1HLFTR | IC PLL ZD BUFFER HS 16-TSSOP |
| ICS674R-01LFT | IC DIVIDER USER CONFIG 28-SSOP |
| ICS525R-11LFT | IC PECL CLK USER CONFIG 28-SSOP |
| DS1844S-100 | IC POT DIG QUAD 100K 20-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS18030-100+ | 功能描述:數字電位計 IC Addressable Dual RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| DS1803-050 | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| DS1803-10 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:IC-10K DUAL POT |
| DS1803-100 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Addressable Dual Digital Potentiometer |
| DS1803-50 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:IC-50K DUAL POT |
發布緊急采購，3分鐘左右您將得到回復。