- 您現在的位置：買賣IC網 > Datasheet目錄39 > DS1624S+T&R (Maxim Integrated)IC THERM/EEPROM DIG 256BYT 8SOIC Datasheet資料下載
參數資料
| 型號： | DS1624S+T&R |
| 廠商： | Maxim Integrated |
| 文件頁數： | 9/18頁 |
| 文件大?。?/td> | 424K |
| 描述： | IC THERM/EEPROM DIG 256BYT 8SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,000 |
| 功能： | 溫度計，恒溫計 |
| 傳感器類型： | 內部 |
| 感應溫度： | -55°C ~ 125°C |
| 精確度： | ±0.5°C（最小值） |
| 拓撲： | EEPROM，寄存器庫 |
| 輸出類型： | 2 線串行 |
| 輸出警報： | 無 |
| 輸出風扇： | 無 |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 工作溫度： | -55°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.209"，5.30mm 寬） |
| 供應商設備封裝： | 8-SO |
| 包裝： | 帶卷 (TR) |
DS1624
f 1
Read Temperature [AAh]
This command reads the last temperature conversion result. The DS1624 will send two bytes in the
format described earlier, which are the contents of this register.
Start Convert T [EEh]
This command begins a temperature conversion. No further data is required. In oneshot mode the
temperature conversion will be performed and then the DS1624 will remain idle. In continuous mode this
command will initiate continuous conversions.
Stop Convert T [22h]
This command stops temperature conversion. No further data is required. This command may be used to
halt a DS1624 in continuous conversion mode. After issuing this command, the current temperature
measurement will be completed, then the DS1624 will remain idle until a Start Convert T is issued to
resume continuous operation.
DS1624 COMMAND SET Table 3
INSTRUCTION
DESCRIPTION
PROTOCOL
2-WIRE BUS
DATA AFTER
ISSUING
PROTOCOL
NOTES
TEMPERATURE CONVERSION COMMANDS
Read
Tem erature
Reads last converted temperature
value from tem erature re ister.
AAh
<read 2 bytes
data>
r
n r T Ini i
m r r
n r i n
EEh
i l
1
Sto Convert T Halts tem erature conversion.
22h
idle
1
THERMOSTAT COMMANDS
Access Memory
Reads or writes to 256-byte
EEPROM memor .
17h
<write data>
2
Access Config
Reads or writes configuration data
nfi r i n r i r
ACh
<write data>
2
1. In continuous conversion mode a Stop Convert T command will halt continuous conversion. To restart, the Start Convert
T command must be issued. In one-shot mode a Start Convert T command must be issued for every temperature reading
desired.
2. Writing to the E
2
typically requires 10ms at room temperature. After issuing a write command, no further reads or writes
should be requested for at least 10ms.
During the programming cycle, the DS1624 will not acknowledge any further accesses to the device until
the programming cycle is complete (no longer than 50ms).
相關PDF資料 |
PDF描述 |
|---|---|
| DS1626S+ | IC THERMOMETER/STAT DIG 8-SOIC |
| DS1629S+T&R | IC THERM/RTC/CALENDAR DIG 8-SOIC |
| DS1631S+T&R | IC THERMOMETER DIG HI-PREC 8SOIC |
| DS1721U+T&R | IC THERMOMETER/STAT DIG HP 8USOP |
| DS1722S | IC THERMOMETER DIG 3-WIRE 8-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1625S | 制造商:Maxim Integrated Products 功能描述:DIGITAL THERMOMETER, 8 Pin, SOP |
| DS1626 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:High-Precision 3-Wire Digital Thermometer and Thermostat |
| DS1626_07 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:High-Precision 3-Wire Digital Thermometer and Thermostat |
| DS1626S | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS1626S+ | 功能描述:板上安裝溫度傳感器 Digital Thermometer & Thermostat RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。